대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제31권5호
  • /
  • Pages.586-593
  • /
  • 2007
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

소변형 이론에 입각한 감육이 존재하는 90 도 곡관의 한계하중 (I) - 내압 -

Plastic Limit Loads of 90° Elbows with Local Wall Thinning using Small Strain FE Limit Analyses (I) - Internal Pressure -

  • 발행 : 2007.05.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This paper proposes closed-form plastic limit load solutions for elbow with local wall thinning at extrados under internal pressure. This work was performed using 3-dimensional, small strain FE analyses based on elastic-perfectly plastic materials. The wide range of elbow and local wall thinning geometries are considered. For systematic analyses for effect of axial thinning extent on limit loads, two limiting cases are considered; a sufficiently long thinning, and the circumferential part-through surface crack. Then, the closed-form plastic limit load solutions for intermediate thinning are obtained by using result of two limiting cases. The effect of axial thinning extent for elbow on plastic limit load is highlighted by comparing with that for straight pipes. Although the proposed limit load solutions are developed for the case when local wall thinning exist in the center of elbow, it is also shown that they can be applied to the case when local wall thinning exists anywhere within elbow.

키워드

참고문헌

  1. Kanninen, M.F., Zahoor, A., Wilkoski, G., Abousayed, I., Marschall, C., Broek, D., Sampath, S., Rhee, H. and Ahmad, J., 1982, 'Instability Predictions for Circumferentially Cracked Type-304 Stainless Pipes Under Dynamic Loading,' EPRI NP-2347, Electric Power Research Institute, Palo Alto, CA
  2. ASME Boiler and Pressure Vessel Code Section IX (1992)
  3. API, API RP579 - Recommended Practice for Fitness-For-Service, 2000, American Petroleum Institute
  4. Choi, J.B., Goo, B.K., Kim, J.C., Kim, Y.J. and Kim, W.S., 2003, 'Development of Limit Load Solutions for Corroded Gas Pipelines,' International Journal of Pressure Vessels and Piping, Vol. 80, pp. 121-128 https://doi.org/10.1016/S0308-0161(03)00005-X
  5. Stephens, D.R. and Lei, B.N., 2000, 'Development of an Alternative Criterion for Residual Strength of Corrosion Defects in Moderate-to High-Toughness Pipe,' Proc. Int. Pipeline Conf., Vol. 2, pp. 781-792
  6. Miyazaki, K., Kanno, S., Ishiwata, M., Hasegawa, K., Ahn, S.H. and Ando, K., 2002, 'Fracture and General Yield for Carbon Steel Pipes with Local Wall Thinning,' Nuclear Engineering and Design, Vol. 211, pp. 61-68 https://doi.org/10.1016/S0029-5493(01)00438-1
  7. Hasegawa, K., Sakata, K., Miyazaki, K. and Kanno S., 2002, 'Fatigue Strength for Pipes with Allowable Flaws and Design Curve,' International Journal of Pressure Vessels and Piping, Vol. 79, pp. 37-44 https://doi.org/10.1016/S0308-0161(01)00129-6
  8. Ahn, S.H., Nam, K.W., Yoo, Y.S., Ando, K., Ji, S.H., Ishiwata, M. and Hasegawa, K., 2002, 'Fracture Behavior of Straight Pipe and Elbow with Local Wall Thinning,' Nuclear Engineering and Design, Vol. 211, pp. 91-103 https://doi.org/10.1016/S0029-5493(01)00447-2
  9. Shim, D.J., Choi, J.B., and Kim, Y.J., 2004, 'Failure Strength Assessment of Pipes with Local Wall Thinning Under Combined Loading Based on Finite Element Analyses,' ASME Journal of Pressure Vessel Technology, Vol. 126, pp. 179-183 https://doi.org/10.1115/1.1687382
  10. Kim, Y.J., Oh, C.K., Park, C.Y., and Hasegawa, K., 2006, 'Net-section Limit Load Approach for Failure Strength Estimates of Pipes with Local Wall Thinning,' International Journal of Pressure Vessels and Piping, Vol. 83, pp. 546-555 https://doi.org/10.1016/j.ijpvp.2006.03.001
  11. Roberston, A., Li, H. and Mackenzie, D., 2005, 'Plastic Collapse of Elbows Under Combined Internal Pressure and In-Plane Bending,' International Journal of Pressure Vessels and Piping, Vol. 82, pp. 407-416 https://doi.org/10.1016/j.ijpvp.2004.09.005
  12. Yahiaoui, K., Moffat, D.G. and Moreton, D.N., 2000, 'Piping Elbows with Cracks - a Parametric Study of the Influence of Crack Size in Limit Loads Due to Pressure and Opening Bending,' Journal of Strain Analysis, Vol. 35, pp. 35-46 https://doi.org/10.1243/0309324001513991
  13. Kim, Y.J. and Oh, C.S., 2006, 'Closed Form Plastic Collapse Loads of Elbows Under Combined Pressure and In-Plane Bending,' Engineering Fracture Mechanics, Vol. 73, pp. 1437-1454 https://doi.org/10.1016/j.engfracmech.2006.02.001
  14. ABAQUS Version 6.2-1. User's manual. Hibbitt, Karlsson and Sorensen, Inc, RI; 2001
  15. Calladine, C.R., 1974, 'Limit Analysis of Curved Tubes,' Journal of Mechanical Engineering Science, Vol. 16, pp. 85-87 https://doi.org/10.1243/JMES_JOUR_1974_016_016_02
  16. Kim, Y.J. and Oh, C.S., 'Effects of Attached Straight Pipes on Finite Element Limit Analysis of Pipe Bends,' International Journal of Pressure Vessels and Piping (electronic version available) https://doi.org/10.1016/j.ijpvp.2006.09.017
  17. Goodall, I.W., 1978, 'Lower Bound Limit Analysis of Curved Tubes Loaded by Combined Internal Pressure and In-Plane Bending Moment,' CEGB report RD/B/N4360 Central Electricity Generating Board
  18. Miller, A.G., 1988, 'Review of Limit Loads of Structures Containing Defects,' International Journal of Pressure Vessels and Piping, Vol. 32, pp. 191-327 https://doi.org/10.1016/0308-0161(88)90073-7
  19. Oh, C.K., Kim, Y.J. and Park, C.Y., 'Quantification of Axial Length Effects on Net-Section Limit Loads for Pipes with Local Wall Thinning Under Combined Pressure and Bending,' International Journal of Pressure Vessels and Piping (submitted)