DOI QR코드

DOI QR Code

Fatigue experiment of stud welded on steel plate for a new bridge deck system

  • Ahn, Jin-Hee (School of Civil and Environmental Engineering, Yonsei University) ;
  • Kim, Sang-Hyo (School of Civil and Environmental Engineering, Yonsei University) ;
  • Jeong, Youn-Ju (Structure Research Department, Korea Institute of Construction Technology)
  • 투고 : 2007.03.21
  • 심사 : 2007.08.27
  • 발행 : 2007.10.25

초록

This paper presents push-out tests of stud shear connectors to examine their fatigue behavior for developing a new composite bridge deck system. The fifteen push-out specimens of D16 mm stud welded on 9 mm steel plate were fabricated according to Eurocode-4, and a series of fatigue endurance test and residual strength test were performed. Additionally, the stiffness and strength variations by cyclic loading were compared. The push-out test, when the stiffness reduction ratio of the specimens was 0.95 under cyclic load, resulted in the failure of the studs. The stiffness variation of the push-out specimens additionally showed that the application of cyclic loads reduced the residual strength. The fatigue strength of the shear connectors were compared with the design values specified in the Eurocode-4, ASSHTO LRFD and JSSC codes. The comparison result showed that the fatigue endurance of the specimens satisfies the design values of these codes.

키워드

참고문헌

  1. Oehlers, D. J. and Bradford, M. A. (1999), Elementary Behavior of Composite Steel & Concrete Structural Members. Butterworth-Heinemannn, Oxford.
  2. Johnson, R. P. (1994), Composite Structures of Steel and Concrete, Blackwell Scientific Publications, London.
  3. Johnson, R. P. (2000),"Resistance of stud shear connectors to fatigue", J. Constr. Steel Res., 56, 101-116. https://doi.org/10.1016/S0143-974X(99)00082-6
  4. Viest, I. M. (1956),"Investigation of stud shear connectors for composite concrete and steel T-beams", J. ACI, 103, 53-77.
  5. Viest, I. M. (1960),"Review of research on composite steel-concrete beams", J. Struct. Div., ASCE, 1-21.
  6. Oehlers, D. J. and Foley, L. (1985),"The fatigue strength of stud shear connectors in composite beams", Proc. Instn Civ. Engrs, Part 2, 79, 349-364. https://doi.org/10.1680/iicep.1985.995
  7. Oehlers, D. J. and Johnson, R. P. (1987),"The strength of stud shear connectors in composite beams", The Structural Engineer, 65B(2), 44-48.
  8. Ellobody, E. and Lam, D. (2002),"Modeling of headed stud in steel-precast composite beams", Steel Compos. Struct., 2(5), 355-378. https://doi.org/10.12989/scs.2002.2.5.355
  9. Shim, C. S., Lee, P. G., Kim, H. H. and Yoon, T. Y. (2003),"Fatigue behavior of large diameter stud shear connectors, J. Korea Society of Steel Constr., 15(6), 621-628.
  10. Hanswille, G., Porsch, M. and Ustundag, C. (2007),"Resistance of headed studs subjected to fatigue loading Part I: Experimental study", J. Constr. Steel Res., 63, 475-484. https://doi.org/10.1016/j.jcsr.2006.06.035
  11. Hanswille, G., Porsch, M. and Ustundag, C. (2007),"Resistance of headed studs subjected to fatigue loading Part II: Analytical study", J. Constr. Steel Res., 63, 485-493. https://doi.org/10.1016/j.jcsr.2006.06.036
  12. Eurocode-4 ENV (1997), Design of Composite Steel and Concrete Structures, European Committee for Standardization (CEN).
  13. Jeong, Y. J., Kim, S. H. and Ahn, J. H. (2005),"Partial-interactive behavior of steel-concrete member under static and fatigue loadings", Mag. Concrete Res., 57(5), 289-300. https://doi.org/10.1680/macr.2005.57.5.289
  14. Jeong, Y. J., Jeong, G. H., Ku, H. B. and Kim, B. S. (2004),"Experimental properties of static behavior of steelconcrete composite bridge decks", Journal of Korean Society of Civil Engineers, 24(1A), 17-25.
  15. Korea Institute of Construction Technology (2005), Development of a Long-life Deck System for Bridges (IV), KICT 2005-057, Korea.
  16. The Japanese Society of Steel Construction (1993), Fatigue Design Recommendations for Steel Structures, Gihodo Shuppan.
  17. AASHTO LRFD (2004), Bridge Design Specifications SI UNIT Third Edition, Washington DC.
  18. Ministry of Construction and Transportation (2005), Design Specification for Highway Bridges, Korea.

피인용 문헌

  1. Fatigue performance of lightweight steel–concrete–steel sandwich systems vol.66, pp.2, 2010, https://doi.org/10.1016/j.jcsr.2009.07.009
  2. Experimental study on joint of spliced steel–PSC hybrid girder, Part I: Proposed parallel-perfobond-rib-type joint vol.33, pp.8, 2011, https://doi.org/10.1016/j.engstruct.2011.04.012
  3. Behaviour of RC beams strengthened by partial jacketing under cyclic loading vol.47, pp.3, 2014, https://doi.org/10.1617/s11527-013-0067-8
  4. Experimental Evaluation of the Shear Resistance of Corrugated Perfobond Rib Shear Connections vol.14, pp.2, 2011, https://doi.org/10.1260/1369-4332.14.2.249
  5. Experimental shear resistance evaluation of Y-type perfobond rib shear connector vol.82, 2013, https://doi.org/10.1016/j.jcsr.2012.12.001
  6. End-bearing resistance of Y-type perfobond rib according to rib width–height ratio vol.103, 2014, https://doi.org/10.1016/j.jcsr.2014.08.003
  7. Shear resistance of the perfobond-rib shear connector depending on concrete strength and rib arrangement vol.66, pp.10, 2010, https://doi.org/10.1016/j.jcsr.2010.04.008
  8. Growth of prestressed concrete bridges with corrugated steel webs in China vol.171, pp.2, 2018, https://doi.org/10.1680/jcien.17.00045
  9. Deterioration in strength of studs based on two-parameter fatigue failure criterion vol.23, pp.2, 2017, https://doi.org/10.12989/scs.2017.23.2.239
  10. Investigation of pipe shear connectors using push out test vol.27, pp.5, 2018, https://doi.org/10.12989/scs.2018.27.5.537
  11. Study of single perfobond rib with head stud shear connectors for a composite structure vol.71, pp.17, 2007, https://doi.org/10.1680/jmacr.18.00051
  12. Experimental study on the hybrid shear connection using headed studs and steel plates vol.37, pp.6, 2020, https://doi.org/10.12989/scs.2020.37.6.649