Steel and Composite Structures

  • 제7권4호
  • /
  • Pages.321-337
  • /
  • 2007
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Investigation of cold-formed stainless steel non-slender circular hollow section columns

  • Ellobody, Ehab (Department of Structural Engineering, Faculty of Engineering, Tanta University) ;
  • Young, Ben (Department of Civil Engineering, The University of Hong Kong)
  • 투고 : 2006.09.13
  • 심사 : 2007.08.13
  • 발행 : 2007.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

The investigation on the behaviour of cold-formed stainless steel non-slender circular hollow section columns is presented in this paper. The normal strength austenitic stainless steel type 304 and the high strength duplex materials (austenitic-ferritic approximately equivalent to EN 1.4462 and UNS S31803) were considered in this study. The finite element method has been used to carry out the investigation. The columns were compressed between fixed ends at different column lengths. The geometric and material nonlinearities have been included in the finite element analysis. The column strengths and failure modes were predicted. An extensive parametric study was carried out to study the effects of normal and high strength materials on cold-formed stainless steel non-slender circular hollow section columns. The column strengths predicted from the finite element analysis were compared with the design strengths calculated using the American Specification, Australian/New Zealand Standard and European Code for cold-formed stainless steel structures. The numerical results showed that the design rules specified in the American, Australian/New Zealand and European specifications are generally unconservative for the cold-formed stainless steel non-slender circular hollow section columns of normal and high strength materials, except for the short columns and some of the high strength stainless steel columns. Therefore, different values of the imperfection factor and limiting slenderness in the European Code design rules were proposed for cold-formed stainless steel non-slender circular hollow section columns.

키워드

참고문헌

  1. ABAQUS Standard User's Manual (2004), Hibbitt, Karlsson and Sorensen, Inc. Vol. 1, 2 and 3, Version 6.4, USA.
  2. ASCE (2002), Specification for the design of cold-formed stainless steel structural members. American Society of Civil Engineers, SEI/ASCE-8-02, Reston, Virginia.
  3. AS (1991), Methods for tensile testing of metals. Australian Standard, AS 1391 - 1991, Standards Association of Australia, Sydney, Australia.
  4. AS/NZS (2001), Cold-formed Stainless Steel Structures. Australian/New Zealand Standard, AS/NZS 4673:2001, Standards Australia, Sydney, Australia.
  5. EC3 (1996), Eurocode 3: Design of steel structures - Part 1.4: General rules - Supplementary rules for stainless steels. European Committee for Standardization, ENV 1993-1-4, CEN, Brussels.
  6. Ellobody, E. and Young, B. (2005),"Structural performance of cold-formed high strength stainless steel columns", J. Constr. Steel Res., 61(12), 1631-1649. https://doi.org/10.1016/j.jcsr.2005.05.001
  7. Gardner, L. (2002),"A new approach to structural stainless steel design", PhD thesis, Department of Civil and Environmental Engineering, Imperial College of Science, Technology and Medicine, London.
  8. Gardner, L. (2005),"The use of stainless steel in structures", Progress in Structural Engineering and Materials, 7(2), 45-55. https://doi.org/10.1002/pse.190
  9. Gardner, L. and Nethercot, D. A. (2004a),"Experiments on stainless steel hollow sections - Part 1: Material and cross-sectional behaviour", J. Constr. Steel Res., 60(9), 1291-1318. https://doi.org/10.1016/j.jcsr.2003.11.006
  10. Gardner, L. and Nethercot, D.A. (2004b),"Experiments on stainless steel hollow sections - Part 2: Member behaviour of columns and beams", J. Constr. Steel Res., 60(9), 1319-1332. https://doi.org/10.1016/j.jcsr.2003.11.007
  11. Gardner, L. and Nethercot, D. A. (2004c),"Numerical modeling of stainless steel structural components - A consistent approach", J. Struct. Eng., ASCE, 130(10), 1586-1601. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:10(1586)
  12. Gardner, L., Talja, A. and Baddoo, N. R. (2006),"Structural design of high-strength austenitic stainless steel", Thin-Walled Struct., 44(5), 517-528. https://doi.org/10.1016/j.tws.2006.04.014
  13. Macdonald, M., Rhodes, J. and Taylor, G. T. (2000),"Mechanical properties of stainless steel lipped channels", Proceedings of the Fifteenth International Specialty Conference on Cold-formed Steel Structures, Eds R. A. LaBoube and W. W. Yu, St. Louis, University of Missouri-Rolla, Mo., USA, 673-686.
  14. Ramberg, W. and Osgood, W.R. (1943),"Description of stress strain curves by three parameters", Tech. Note No 902, National Advisory committee for Aeronautics, Washington, D.C.
  15. Rasmussen, K. J. R. (2000),"Recent research on stainless steel tubular structures", J. Constr. Steel Res., 54, 75-88. https://doi.org/10.1016/S0143-974X(99)00052-8
  16. Rasmussen, K. J. R. and Hancock, G. J. (1993),"Design of cold-formed stainless steel tubular members. I: Columns", J. Struct. Eng., ASCE, 119(8), 2349-2367. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:8(2349)
  17. Rasmussen, K.J.R. and Rondal, J. (1997),"Strength curves for metal columns", J. Struct. Eng., ASCE, 123(6), 721-728. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:6(721)
  18. Talja, A. and Salmi, P. (1995),"Design of stainless steel RHS beams, columns and beam-columns", VTT Research Notes 1619, Technical Research Centre of Finland, Espoo.
  19. Young, B. and Ellobody, E. (2006),"Column design of cold-formed stainless steel slender circular hollow sections", Steel Compos. Struct., 6(4), 285-302. https://doi.org/10.12989/scs.2006.6.4.285
  20. Young, B. and Hartono, W. (2002),"Compression tests of stainless steel tubular members", J. Struct. Eng., ASCE, 128(6), 754-761. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:6(754)
  21. Young, B. and Liu, Y. (2003),"Experimental investigation of cold-formed stainless steel columns", J. Struct. Eng., ASCE, 129(2), 169-176. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:2(169)
  22. Young, B. and Lui, W. M. (2005),"Behavior of cold-formed high strength stainless steel sections", J. Struct. Eng., ASCE, 131(11), 1738-1745. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:11(1738)
  23. Young, B. and Rasmussen, K. J. R. (1998),"Tests of fixed-ended plain channel columns", J. Struct. Eng., ASCE, 124(2), 131-139. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(131)

피인용 문헌

  1. Structural response of stainless steel oval hollow section compression members vol.31, pp.4, 2009, https://doi.org/10.1016/j.engstruct.2008.12.002
  2. Nonlinear behaviour of built-up cold-formed steel section battened columns vol.110, 2015, https://doi.org/10.1016/j.jcsr.2015.03.007
  3. A consistent nonlinear approach for analysing steel, cold-formed steel, stainless steel and composite columns at ambient and fire conditions vol.68, 2013, https://doi.org/10.1016/j.tws.2013.02.016
  4. Structural behaviour of stainless steel stub column under axial compression: a FE study pp.2093-6311, 2018, https://doi.org/10.1007/s13296-018-0083-1
  5. Design of cold-formed stainless steel circular hollow section columns using direct strength method vol.163, pp.None, 2007, https://doi.org/10.1016/j.engstruct.2018.02.012
  6. An Experimental Study on the Buckling Behaviors of Stainless Steel Tubular Columns Under Concentric Axial Compression vol.31, pp.4, 2007, https://doi.org/10.7781/kjoss.2019.31.4.273
  7. A unified approach for austenitic and ferritic stainless steel CHS beam–columns subjected to eccentric loading vol.165, pp.None, 2007, https://doi.org/10.1016/j.tws.2021.107918
  8. Tensile behavior of stainless steel S30408 at the Arctic low temperature vol.40, pp.5, 2007, https://doi.org/10.12989/scs.2021.40.5.633
  9. Flexural buckling of stainless steel CHS columns: Reliability analysis utilizing FEM simulations vol.188, pp.None, 2007, https://doi.org/10.1016/j.jcsr.2021.107002