Analysis of Correlativity with the Number of Blasting Holes Due to Exposed Length of Steel Bars and Vertical Load on Scaled Reinforced Concrete Columns

축소모형 철근콘크리트 기둥에서 철근의 노출길이와 수직하중에 따른 발파공수와의 상관성 분석

  • 박훈 (전북대학교 공업기술연구소) ;
  • 유지완 (전북대학교 자원.에너지공학과) ;
  • 이희광 (전북대학교 자원.에너지공학과) ;
  • 송정언 (전북대학교 자원.에너지공학과) ;
  • 김승곤 (전북대학교 자원.에너지공학과)
  • Published : 2007.12.31

Abstract

In this paper, the 1/5 scale models of the reinforced concrete colunms were designed and fabricated. The influence of the number of blasting holes on the exposed length of steel bars and vertical load was investigated. The relation between the length of steel bar and the number of blasting holes was examined by performing the blast tests considering the vertical load on the scaled reinforced concrete columns. Weight of scaled column models by blasting and that of exposed was compared with the number of blasting holes. Finally, based on the exposed length of steel bars and vertical load, the number of blasting holes were calculated. Results shows that the number of blasting holes calculated in this study are suitable for scaled structure models test by blasting demolition.

본 연구에서는 1/5 축소모형 철근콘크리트 기둥을 이용하여 철근의 노출길이 및 수직하중과 발파공수와의 관계에 대해 연구하였다. 축소모형 철근콘크리트 기둥에 수직하중을 재하하여 철근의 노출 길이와 발파공수와의 관계를 비교하였다. 또한 발파된 축소모형 기둥의 무게와 철근이 노출된 축소모형 기둥의 무게를 발파공수와 비교하였다. 축소모형 철근콘크리트 기둥에 대한 시험결과로부터 철근의 노출길이 및 수직하중을 바탕으로 축소모형 철근콘크리트 기둥의 발파공수를 산정할 수 있으며, 이를 축소모형 구조물에 적용할 수 있음을 확인하였다.

Keywords

References

  1. 김남식, 곽영학, 장승필, 2003, Modified simulation law for pseudodynamic test on small-scale steel models, 한국지진공학회 논문집, Vol. 7, No.6, pp. 49-57
  2. 김남식, 이지호, 장승필, 2004, RC 축소모형의 유사동적실험을 위한 Equivalent multi-phase similitude law : 검증실험, 한국지진공학회 논문집, Vol. 8, No. 5, pp. 35-43
  3. 김승곤, 박훈, 양형식, 2002, 콘크리트 기둥의 발파해체시 파쇄도에 미치는 수직하중의 영향, 화약.발파, Vol. 20, No. 3, pp. 97-109
  4. 박훈, 유지완, 이희광, 김승곤, 2007, 철근콘크리트 구조물의 축소모형 부재 제작 및 역학적 특성, 대한화약발파공학회 춘계학술발표회 논문집, 전주, pp.1-10
  5. Kumar, S., Y. Itoh, K. Saizuka and T. Usami, 1997, Pseudodynamic testing of scaled models, Journal of Structural Engineering, Vol. 123, No.4, pp. 524-526 https://doi.org/10.1061/(ASCE)0733-9445(1997)123:4(524)