International Journal of Automotive Technology

The Korean Society of Automotive Engineers (한국자동차공학회)
권호 표지

PERFORMANCE CHARACTERISTICS OF A PROTON EXCHANGE MEMBRANE FUEL CELL(PEMFC) WITH AN INTERDIGITATED FLOW CHANNEL

  • Lee, P.H. (Department of Mechanical Engineering, University of Incheon) ;
  • Cho, S.A. (Department of Mechanical Engineering, University of Incheon) ;
  • Han, S.S. (Department of Mechanical Engineering, University of Incheon) ;
  • Hwang, S.S. (Department of Mechanical Engineering, University of Incheon)
  • Published : 2007.12.01
Download PDF
⟨ Previous Next ⟩

Abstract

The configuration of the flow channel on a bipolar plate of a proton exchange membrane fuel cell(PEMFC) for efficient reactant supply has great influence on the performance of the fuel cell. Recent demand for higher energy density fuel cells requires an increase in current density at mid voltage range and a decrease in concentration overvoltage at high current density. Therefore, an interdigitated flow channel where mass transfer rate by convection through a gas diffusion layer is greater than the mass transfer by a diffusion mechanism through a gas diffusion layer was recently proposed. This study attempts to analyze the i-V performance, mass transfer and pressure drop in interdigitated flow channels by developing a fully three dimensional simulation model for PEMFC that can deal with anode and cathode flow together. The results indicate that the trade off between performance and pressure loss should be considered for efficient design of flow channels. Although the performance of the fuel cell with interdigitated flow is better than that with conventional flow channels due to a strong mass transfer rate by convection across a gas diffusion layer, there is also an increase in friction due to the strong convection through the porous diffusion layer accompanied by a larger pressure drop along the flow channel. It was evident that the proper selection of the ratio of channel and rib width under counter flow conditions in the fuel cell with interdigitated flow are necessary to optimize the interdigitated flow field design.

Keywords

References

  1. Birgersson, E. and Vynnycky, M. (2006). A quantitative study of the effect of flow-distributor geometry in the cathode of a PEM fuel cell. J. Power Soc., 153, 76−88
  2. Dutta, S., Shimpalee, S. and Van Zee, J. W. (2001). Numerical prediction of mass-exchange between anode and cathode channels in a PEM fuel cell. Int. J. Heat and Mass Transfer, 44, 2029−2042
  3. Fuller, T. F. and Newman, J. (1993). Water and thermal management in solid polymer electrolyte fuel cells. J. Electrochem. Soc., 140, 1218−1225
  4. Hu, G. and Fan, J. (2004). Three-dimensional numerical analysis of proton exchange membrane fuel cell (PEMFCs) with conventional and intrdigitated flow fields. J. Power Soc., 136, 1−9
  5. Kazim, A., Liu, H. T. and Forges, P. (1999). Modeling of performance of PEM fuel cells with conventional flow field. J. Appl. Electrochem., 26, 1409−1416
  6. Kim, H. G., Kim, Y. S., and Shu, Z. (2006). Simulation of unit cell performance in the polymer electrolyte membrane fuel cell. Int. J. Automotive Technology 7, 7, 867−872
  7. Lee, W. K., Ho, C. H., Zee, J. W. V. and Murthy, M. (1999). The effects of compreddion and gas diffusion layers on the performance of a PEM fuel cell. J. Power Soc., 84, 45−51
  8. Lee, W. K., Van Zee, J. W., Shimpalee, S. and Dutta, S. (1999). Effect of humidity on PEM fuel cell performance part I-Experiments. Int. Mechanical Engineering Congress & Exposition, 359−366
  9. Nguyen, T. V. and White, R. E. (1993). A water and heat management models for proton exchange membrane fuel cells. J. Electrochem. Soc., 140, 2178−2186
  10. Rawool, A. S., Mitra, S. K. and Pharoah, J. G. (2006). An investigation of convective transport in micro protonexchange membrane fuel cells. J. Power Soc., 162, 985 https://doi.org/10.1016/j.jpowsour.2006.07.067
  11. Srinivasan, S., Ticianelli, E. A., Derouin, C. R. and Redondo, A. (1988). Advances in solid polymer electrolyte fuel cell technology with low platinum loading electrodes. J. Power Soc., 22, 359−375
  12. Um, S. (2003). Computational modeling of Transport and Electrochemical Reaction in Proton Exchange Membrane Fuel Cell. Ph. D. Dissertation. Penn State University. USA
  13. Um, S. and Wang, C. Y. (2000). Three dimensional analysis of transport and reaction in proton exchange membrane fuel cells. Proc. ASME Fuel Cell Division
  14. Shimpalee, S., Dutta, S. and Van Zee, J. W. (2000). Numerical prediction of local temperature and current density in a PEM fuel cell. IMECE, Session of Transport Phenomena in Fuel Cell System, 26−32
  15. Shimpalee, S., Dutta, S., Lee, W. K. and Van Zee, J. W. (1999). Effect of humidity on PEM fuel cell performance part I-Numerical simulation. Proc. ASME IMECH, TN, HTD 364-1, 367−374
  16. Springer, T. E., Zawodzinski, T. A. and Gottesfeld, S. (1991). Polymer electrolyte fuel cell model. J. Electrochem. Soc., 138, 2334−2342 https://doi.org/10.1149/1.2085972
  17. Trung and Nguyen, V. (1996). A gas distributor design for Proton exchange membrane fuel cell. J. Electrochem. Soc., 143, L103−L105
  18. Um, S. and Wang, C. (2004). Three-dimensional analysis of transport and electrochemical reactions in polymer electrolyte fuel cells. J. Power Soc., 125, 40−51
  19. Wang, L., Husar, A., Zhou, T. and Liu, H. (2003). A parametric study of PEM fuel cell performances. Int. J. Hydrogen Energy, 28, 1263−1272
  20. Yi, J. S. and Nguyen, T. V. (1998). An along the channel model for proton exchange membrane fuel cells. J. Electrochem. Soc., 145, 1149−1159
  21. Yi, J. S. and Nguyen, T. V. (1999). Multicomponent transport in porous electrodes of proton exchange membrane fuel cell using the interdigitated gas distributors. J. Electrochem. Soc., 146, 1149−1159