한국분말재료학회지 (Journal of Powder Materials)

  • 제14권6호
  • /
  • Pages.380-385
  • /
  • 2007
  • /
  • 2799-8525(pISSN)
  • /
  • 2799-8681(eISSN)
한국분말재료학회 (*구 분말야금학회) (The Korean Powder Metallurgy & Materials Institute)
권호 표지
DOI QR코드

DOI QR Code

폐 스테인레스강 단섬유로 강화한 알루미늄 복합분말의 자기펄스압 성형 및 소결 특성

Magnetic Pulsed Compaction and Sintering Characteristics of Al Composite Powders Reinforced with Waste Stainless Steel Short Fibers

  • 현창용 (서울산업대학교 신소재공학과) ;
  • 원철현 (서울산업대학교 신소재공학과) ;
  • 박재순 (한국원자력연구원 핵연료가공 Lab)
  • Hyun, Chang-Yong (Department of Materials Science and Engineering, Seoul National University of Technology) ;
  • Won, Chul-Hyun (Department of Materials Science and Engineering, Seoul National University of Technology) ;
  • Park, Jae-Soon (Korea Atomic Energy Research Institute)
  • 발행 : 2007.12.28
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Characteristics of Al-based composites with waste stainless steel short fiber, fabricated by magnetic pulsed compaction and sintering were investigated. The compacts prepared by magnetic pulsed compaction showed high relative density and homogeneous microstructure compared with that by conventional press compaction. The relative density of sintered composites at $430^{\circ}C$ for 1 h exhibited the same value with compacts and decreased with increase in STS short fiber content. The reaction between Al and STS phase was confirmed by the microstructural analysis using EDS. The sintered composites, prepared by magnetic pulsed compaction, showed increased hardness value with increasing STS fiber content. Maximum yield strength of 100 MPa and tensile strength of 232 MPa were registered in the AI-based composite with 30 vol% STS short fiber.

키워드

참고문헌

  1. I. J. Polmear: Light Alloys-Metallurgy of the Light Metals, Butterworth-Heinemann, London (1995) 325
  2. Y. Genma, Y. Tsunekawa, M. Okumiya and N. Mohri: Mater. Trans. JIM, 38 (1997) 232 https://doi.org/10.2320/matertrans1989.38.232
  3. F. Tang, I. E. Anderson, T. Gnaupel-Herold and H. Prask: Mater. Sci. Eng. A, 383 (2004) 362 https://doi.org/10.1016/j.msea.2004.05.081
  4. S.-H. Lee and H.-W. Kim: J. Korean Powder Metall. Inst., 13 (2006) 39 (Korean) https://doi.org/10.4150/KPMI.2006.13.1.039
  5. R. B. Bhagat: Metall. Trans. A, 16 (1985) 623 https://doi.org/10.1007/BF02814236
  6. D. Mandal, B. K. Dutta and S. C. Panigrahi: Wear, 257 (2004) 654 https://doi.org/10.1016/j.wear.2004.02.006
  7. G. H. Lee, C. K. Rhee, M. K. Lee, W. W. Kim and V. V. Ivanov: Mater. Sci. Eng. A, 375-377 (2004) 604 https://doi.org/10.1016/j.msea.2003.10.100
  8. J. K. Lee, S. J. Hong, M. K. Lee and C. K. Rhee: J. Korean Powder Metall. Inst., 12 (2005) 345 (Korean) https://doi.org/10.4150/KPMI.2005.12.5.345
  9. J.-H. AIm, Y. Choi and D. Kwon: J. Kor. Inst. Met. & Mater., 38 (2000) 1606 (Korean)
  10. J.-I. Jang, D. Son, Y. Choi, D. Kwon, S.K. Park and W.S. Kim: Journal of KWS, 20 (2002) 160 (Korean)
  11. G. H. Lee, C. K. Rhee, W. W. Kim, J. W. Yun and K. S. Lee: J. Korean Powder Metall. Inst., 12 (2005) 24 (Korean) https://doi.org/10.4150/KPMI.2005.12.1.024
  12. L. C. Steams, J. Zhao and M. P. Harmer: J. Eur. Cer. Soc., 10 (1992) 473 https://doi.org/10.1016/0955-2219(92)90022-6
  13. R. P. Baron, J. A. Wert, D. A. Gerard and F. E. Wawner: J. Mater. Sci., 32 (1997) 6435 https://doi.org/10.1023/A:1018686505563
  14. Young Ho Kim: M. S. Thesis, Seoul National University of Technology, (2006) (Korean)