참고문헌
- Baaijens, F. P. T. 1991, Calculation of residual stresses in injection molded products, Rheol. Acta 30, 284-299 https://doi.org/10.1007/BF00366642
- Ballman, R. L. and H. L. Torr, 1960, Modern Plastics 38, 113
- Batoz, J. L., K. J. Bathe and L. W. Ho, 1980, Study of three-node triangular plate bending elements, International Journal for Numerical Methods in Engineering 15, 1771-1812 https://doi.org/10.1002/nme.1620151205
- Bergan, P. G. and C. A. Felippa, 1985, Triangular membrane element with rotational degrees of freedom, Computer Methods in Applied Mechanics and Engineering 50, 25-69 https://doi.org/10.1016/0045-7825(85)90113-6
- Bushko, W. C. and V. K. Stokes, 1995a, Solidification of thermoviscoelastic melts. part I: formulation of model problem, Polym. Eng. Sci. 35, 351-364 https://doi.org/10.1002/pen.760350409
- Bushko, W. C. and V. K. Stokes, 1995b, Solidification of thermoviscoelastic melts. part II: effects of processing conditions on shrinkage and residual stresses. Polym. Eng. Sci. 35, 365-384 https://doi.org/10.1002/pen.760350410
- Chiang, H. H., C. A. Hieber and K.K. Wang, 1991a, A nuified simulation of the filling and postfilling stages in injection molding. part I: formulation, Polym. Eng. Sci. 31, 116-124 https://doi.org/10.1002/pen.760310210
- Chiang, H. H., C. A. Hieber and K.K. Wang, 1991b, A nuified simulation of the filling and postfilling stages in injection molding. part II: experimental verification, Polym. Eng. Sci. 31, 125-139 https://doi.org/10.1002/pen.760310211
- Chiang, H. H., K. Himasekhar, N. Santhanam and K. K. Wang, 1993, Integrated simulation of fluid flow and heat transfer in injection molding for the prediction of shrinkage and warpage, J. Eng. Mat. And Tech. 115, 37-47 https://doi.org/10.1115/1.2902155
- Coxon, L. D. and J. R. White, 1979, Measurement of internal stresses in chemically cross-linked high-density polyethylene, J. Mater. Sci. 14, 1114-1120 https://doi.org/10.1007/BF00561295
- Coxon, L. D. and J. R. White, 1980, Residual stresses and aging in injection molded polypropylene, Polym. Eng. Sci. 20, 230-236 https://doi.org/10.1002/pen.760200311
- Dietz, W. and J. L. White, 1978, Ein einfaches Modell zur Berechnung des Druckverlustes wahrend des Werkzeugfullvorganges und der eingefrorenen Orientierung beim Spritzgiessen amorpher Kunststoffe, Rheol. Acta 17, 676-692 https://doi.org/10.1007/BF01522040
- Flaman, A. A. M., 1993a, Buildup and relaxation of molecular orientation in injection molding. part I: formulation, Polym. Eng. Sci. 33, 193-201 https://doi.org/10.1002/pen.760330402
- Flaman, A. A. M., 1993b, Buildup and relaxation of molecular orientation in injection molding. part II: experimental verification, Polym. Eng. Sci. 33, 202-210 https://doi.org/10.1002/pen.760330403
- Friedrichs, B., M. Horie and Y. Yamaguchi, 1996, Simulation and analysis of birefringence in magneto-optical discs. part A: formulation, J. Materials Processing & Manuf. Sci. 5, 95-113
- Ghoneim H. and C. A. Hieber, 1997, Incorporation of density relaxation in the analysis of residual stresses in molded parts, Polym. Eng. Sci. 37, 219-227 https://doi.org/10.1002/pen.11664
- Greener, J. and G. H. Pearson, 1983, Orientation residual stresses and birefringence in injection molding, J. Rheol. 27, 116-134
- Hastenberg, C. H. V., P. C. Wildervanck, A. J. H. Leenen and G.G. J. Schennink, 1992, The measurement of thermal stress distributions along the flow path in injection-molded flat plates, Polym. Eng. Sci. 32, 506-515 https://doi.org/10.1002/pen.760320708
- Isayev, A. I. and C. A. Hieber, 1980, Toward a viscoelastic modelling of the injection molding of polymers, Rheol. Acta 19, 168-182 https://doi.org/10.1007/BF01521928
- Isayev, A. I., 1983, Orientation development in the injection molding of amorphous polymers, Polym. Eng. Sci. 23, 271-284 https://doi.org/10.1002/pen.760230507
- Isayev, A. I. and D. L. Crouthamel, 1984, Residual stress development in the injection molding of polymers, Polymer-plastics technology and engineering 22, 177-232 https://doi.org/10.1080/03602558408070038
- Janeschitz-Kriegl, H., 1983, Polymer melt rheology and flow birefringence, Springer-Verlag, Berlin
- Kaliske, M. and R. Rothert, 1997, Formulation and implementation of three-dimensional viscoelasticity at small and finite strains, Computational Mechanics 19, 228-239 https://doi.org/10.1007/s004660050171
- Kamal, M. R. and V. Tan, 1979, Orientation in injection molded polystyrene, Polym. Eng. Sci. 19, 558-563 https://doi.org/10.1002/pen.760190806
- Famili, N. and A.I. Isayev, 1991, Modeling of Polymer Processing, Hanser Publisher, New York
- Kim, I. H., S. J. Park, S. T. Chung and T. H. Kwon, 1999a, Numerical modeling of injection/compression molding for center-gated disk: part I: injection molding with viscoelastic compressible fluid model, Polym. Eng. Sci. 39, 1930-1942 https://doi.org/10.1002/pen.11586
- Kim, I. H., S. J. Park, S. T. Chung and T. H. Kwon, 1999b, Numerical modeling of injection/compression molding for center-gated disk: part II: effect of compression stage, Polym. Eng. Sci. 39, 1943-1951 https://doi.org/10.1002/pen.11587
- Lee, Y. B. and T. H. Kwon, 2002a, Numerical prediction of residual stresses and birefringence in injection/compression molded center-gated disk. part I: basic modeling and results for injection molding, Polym. Eng. Sci. 42, 2246-2272 https://doi.org/10.1002/pen.11114
- Lee, Y. B. and T. H. Kwon, 2002b, Numerical prediction of residual stresses and birefringence in injection/compression molded center-gated disk. part II: Effects of processing conditions, Polym. Eng. Sci. 42, 2273-2292 https://doi.org/10.1002/pen.11115
- Lee, Y. B. and T. H. Kwon, 2001, PPS 17th Annual meeting, PPS-17
- Leonov, A. I., 1976, Nonequilibrium thermodynamics and rheology of viscoelastic polymer media, Rheol. Acta 15, 85-98 https://doi.org/10.1007/BF01517499
- Leonov, A. I., E. H. Lipkina, E. D. Paskhin and A. N. Prokunin, 1976, Theoretical and experimental investigation of shearing in elastic polymer, Rheol. Acta 15, 411-426 https://doi.org/10.1007/BF01574496
- Mandell, J. F., K. L. Smith and D. D. Huang, 1981, Effects of residual stress and orientation on the fatigue of injection molded polysulfone, Polym. Eng. Sci. 21, 1173-1180 https://doi.org/10.1002/pen.760211711
- Pham, H. T., C. P. Bosnyak and K. Sehanobish, 1993, Residual stresses in injection molded polycarbonate rectangular bars, Polym. Eng. Sci. 33, 1634-1643 https://doi.org/10.1002/pen.760332408
- Russell, D. P. and P. W. R. Beaumont, Structure and properties of injection-moulded nylon-6 - part 2 residual stresses in injection-moulded nylon-6, J. Mater. Sci., 15, 208-215 https://doi.org/10.1007/BF00552446
- Santhanam, N., 1992, PhD thesis, Cornell university, Ithaca, N.Y
- Sandilands, G. J. and J. R. White, 1980, Effect of injection pressure and crazing on internal stresses in injection-moulded polystyrene, Polymer 21, 338-343 https://doi.org/10.1016/0032-3861(80)90278-5
- Shyu, G. D. and A. I. Isayev, 1995, Residual stresses and birefringence in injection molded disks, SPE ANTEC Tech. Papers 41, 2911-2917
- Shyu, G. D., 1993, PhD thesis, The university of Akron
- Siegmann, A., A. Buchman and S. Kenig, 1982, Residual stresses in polymers - 3. the influence of injection-molding process conditions, Polym. Eng. Sci. 22, 560-568 https://doi.org/10.1002/pen.760220908
- Treuting, R. G. and W. T. Read Jr., 1951, A mechanical determination of biaxial residual stress in sheet materials, J. Appl. Phys. 22, 130-134 https://doi.org/10.1063/1.1699913
- Wales, J. L. S., Ir J. Van Leeuwen and R. Van Der Vijgh, 1972, Some aspects of orientation in injection molded objects, Polym. Eng. Sci. 12, 358-363 https://doi.org/10.1002/pen.760120508
- White, J. L., 1991, Principles of polymer engineering rheology, John Wiley & Sons, New York