Journal of Mechanical Science and Technology

  • 제20권9호
  • /
  • Pages.1436-1448
  • /
  • 2006
  • /
  • 1738-494X(pISSN)
  • /
  • 1976-3824(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지

Influence of Injection Rate Shaping on Combustion and Emissions for a Medium Duty Diesel Engine

  • Benajes, J. (Universidad Politecnica de Valencia. CMT-Motores Termicos, Camino de Vera) ;
  • Molina, S. (Universidad Politecnica de Valencia. CMT-Motores Termicos, Camino de Vera) ;
  • Rudder, K. De (Universidad Politecnica de Valencia. CMT-Motores Termicos, Camino de Vera) ;
  • Rente, T. (Chalmers University of Technology)
  • 발행 : 2006.09.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.

키워드

참고문헌

  1. Ahmad, T. and Plee, S. L., 1983, 'Application of Flame Temperature Correlations to Emissions from a Direct-Injection Diesel Engine,' SAE paper, No. 831734
  2. Arcoumanis, C. and Baniasad, M.S., 1993, 'Analysis of Consecutive Fuel Injection Rate Signals Obtained by the Zeuch anD Bosch Methods,' SAE paper, Np. 930921
  3. Baert, R. S. G., Beckman, D. E. and Veen, A., 1999, 'Efficient EGR Technology for Future HD Diesel Engine Emission Targets,' SAE Paper, No. 1999-01-0837
  4. Beck, N. J. and Chen, S. K, 2000, 'Injection Rate Shaping and High Speed Combustion Analysis - New Tools for Diesel Engine Combustion Development,' SAE paper, No. 2000-01-0705
  5. Bosch, W., 1966, 'The Fuel Rate Indicator: A new Measuring Instrument for Display of the Characteristics of Individual Injection,' SAE paper, No. 660749
  6. Chomiak, J. and Karlsson, A., 1996, 'Flame Liftoff in Diesel Sprays,' Twenty-Sixth Symposium (International) on Combustion/ The Combustion Institute, pp.2557-2564
  7. Christian, R., Knopf, F., Jasmek, A. and Schindler, W., 1993, 'A New Method for the Filter Smoke Number Measurement with Improved Sensitivity,' (in German), MTZ 54, pp. 16-22
  8. Desantes, J. M., Arregle, J., Molina, S., 2000, 'Influence of the EGR Rate, Oxygen Concentration and Equivalent Fuel/Air Ratio on the Combustion Behaviour and Pollutant Emissions of a Heavy Duty Diesel Engine,' SAE Paper, No. 2000-01-1813
  9. Erlach, H. et al., 1995, 'Pressure Modulated Injection and its Effect on Combustion and Emissions of a HD Diesel Engine,' SAE paper, No. 952059
  10. Garcia, J., Gil, A. and Estelles, V., 2000, 'The-oretical and Experimental Model for the Burnt Products of Combustion Temperature Calculating on Direct Injection Diesel Engines,' (in Spanish), XIV Congreso Nacional de Ingenieria Mecdnica, Anales de Ingenieri a Mecanica, Ano 13, Vol. 2, pp. 2023-2028
  11. Heywood, J. B., 1988, Internal Combustion Engine Fundamentals, McGraw-Hill, New York
  12. Ishida, M., Ueki, H., Matsumura, N., Yamaguchi, M. and Luo, G. F., 1996, 'Diesel Combustion Analysis Based on Two Zone Model (Comparison Between Model Analysis and Experiment),' JSME Int. Journal, Series B, Vol. 39, No.1, pp.185-192 https://doi.org/10.1299/jsmeb.39.185
  13. Ishiwate, H. et al., 1994, 'Recent Progress in Rate Shaping Technology for Diesel In-line Pumps,' SAE paper, No. 940194
  14. Jeongkuk, Y. et al., 2004, 'A Study on the Behavior of Evaporating Diesel Spray Using LIEF Measurement and KIVA code,' KSME I. J., Vol. 18, No. 12, pp. 2303-2309
  15. Jinwook, L. and Kyoungdoug, M., 2005, 'Effects of Needle Response on Spray Characteristics in High Pressure Injector Driven by Piezo Actuator for Common-Rail Injection System,' KSME I. J., Vol. 19, No. 5, pp. 1194-1205 https://doi.org/10.1007/BF02984041
  16. Jinwook, L., Kyoungdoug, M., Kernyong, K. and Choongsik, B., 2006, 'Hydraulic Simulation and Experimental Analysis of Needle Response and Controlled Injection Rate Shape Characteristics in a Piezo-Driven Diesel Injector,' SAE paper, No. 2006-01-1119
  17. Juneja, H., Ra, Y. and Reitz, R. D., 2004, 'Optimization of Injection Rate Shape Using Active Control of Fuel Injection,' SAE paper, No. 200401-0530
  18. Kato, T. et al., 1998, 'Common Rail Fuel Injection System for Improvement of Engine Performance on Heavy-Duty Diesel Engine,' SAE paper, No. 980806
  19. Kazuhiro, A. and Uoshiki T., 2001, 'Mechanism of the Smokeless Rich Diesel Combustion by Reducing Temperature,' SAE paper, No. 200101-0655
  20. Kobori, S., Kamimoto, T. and Aradi, A., 2000, 'A Study of Ignition Delay of Diesel Fuel Sprays,' Int.J. Engine Research, Vol. 1, No. 1, pp. 29-39 https://doi.org/10.1243/1468087001545245
  21. Kohketsu, S., Tanabe, K. and Mori, K., 2000, 'Flexibly Controlled Injection Rate Shape with Next Generation Common Rail System for Heavy-Duty DI Desel Engines,' SAE paper, No. 200001-0705
  22. Kyu Keun, S., Sang Cherl, S. and Jang Heon, K., 2005, 'Effect of the Injection Parameters on Diesel Spray Characteristics,' KSME I. J., Vol. 19, No. 6, pp. 1321-1328 https://doi.org/10.1007/BF02984052
  23. Lapuerta, M., Armas, O. and Bermudez, V., 2000, 'Sensitivity of Diesel Engine Thermodynamic Cycle Calculation to Measurement Errors and Estimated Parameters,' Applied Thermal Engineering, Vol. 20, No. 9, pp. 843-861 https://doi.org/10.1016/S1359-4311(99)00069-1
  24. Lapuerta, M., Armas, O. and Hernundez, J. J., 1999, 'Diagnostic of D. I. Diesel Combustion from In-Cylinder Pressure Signal by Estimation of Mean Thermodynamic Properties of the Gas,' Applied Thermal Engineering, Vol. 5, pp. 513-519 https://doi.org/10.1016/S1359-4311(98)00075-1
  25. Lavoie, G., Heywood, J. and Keck, J., 1970, 'Experimental and Theoretical Study of Nitric Oxide Formation in Internal Combustion Engines,' Combusion Science and Technology, Vol. 1, pp. 313-326 https://doi.org/10.1080/00102206908952211
  26. Nehmer, D. A. and Reitz, R. D., 1994, 'Measurement of the Effect of Injection Rate and Split Injections on Diesel Engine Soot and NOx Emissions,' SAE paper, No. 940668
  27. Payri, R., Salvador, F. J., Gimeno, J. and Soare, V., 2005, 'Determination of Diesel Sprays Characteristics in Real Engine in-Cylinder Air Density and Pressure Conditions,' KSME I. J., Vol. 19, No. 11, pp. 2040-2052 https://doi.org/10.1007/BF02916497
  28. Pierpont, D. A., Montgomery, D. T. and Reitz, R.D., 1995, 'Reducing Particulate and NOx Using Multiple Injections and EGR in a D. I. Diesel,' SAE Paper, No. 950217
  29. Rosseel, E. and Sierens, R., 1996, 'The Physical and the Chemical Part of the Ignition Delay in Diesel Engines,' SAE paper, No. 961123
  30. Schwarz, V. et al., 1999, 'Analysis of Mixture Formation, Combustion and Pollutant Formation in HD Diesel Engines Using Modern Optical Diagnostics and Numerical Simulation,' SAE paper, No. 1999-01-3647