초록
본 연구에서는 점성토의 강도를 증진시키기 위해, 일련의 동전기 주입 안정화 실내 실험을 수행하였다. 이를 위해 규산나트륨을 주입제로 선정하고 농도를 변화(500, 1000, 1500, 2000, 2500mM)시켜 동전기 주입 안정화 기법의 적용성을 파악하였고, 처리기간과 전압경사에 따른 영향을 파악하기 위해 2일 간격(2, 4, 6, 8, 10일)으로 처리기간을 설정한 실험과 0.25, 0.5, 1.0, 1.5, 2.0V/cm로 전압경사를 변화시킨 실험을 실시하였다. 또한 염화칼슘과 수산화알루미늄을 2차 주입제로 사용하여 첨가농도에 따른 전단강도 개량 효과를 파악하고자 하였다. 이를 위해 규산나트륨(1000mM)을 5일간 적용한 후 2차 주입제의 농도를 50, 250, 500, 750, 1000mM로 변화시켜 5일간 적용하였다. 규산나트륨의 농도 결정시험결과 1000mM 이상의 농도에서 일정한 값으로 수렴하는 양상을 띠었으며, 이 때 초기 강도보다 약 800% 크게 강도증진효과가 나타났다. 최적전기경사와 처리기간 결정시험결과 전압의 경우 1V/cm, 처리기간의 경우 6일 이상에서 강도증가치가 수렴하는 양상이 나타났다. 염화칼슘과 수산화알루미늄을 2차 주입제로 사용한 경우, 두 경우 모두 250mM 이상의 농도에서 일정한 강도값으로 수렴하는 양상이 나타났으며, 규산나트륨만 사용한 경우보다 약 20~30%의 강도증진효과가 발생했다.
In this study a series of bench scale test are conducted to increase the undrained shear strength of clayey soils using by Electro-kinetic injection stabilization method. The sodium silicate was injected in anode reservoir and its concentration was changed with 500, 1000, 1500, 2000, 2500mM for configuration of applicability of Electro-kinetic injection stabilization method. Also, the treatment time and electric gradient was changed to acquire the optical influence factors. For increasing the shear strength to maximum values, the calcium chloride and aluminium hydroxide, which concentration was changed with 50, 250, 500, 750, 1000mM, were added at anode reservoir for 5 days after the treatment of sodium silicate in 5 days as the 2nd additives. The test of results in determination of sodium silicate concentration show that the undrained shear strength at each point had a tendency to converge into a constant value when the concentration of sodium silicate came to 1000mM and above. The maximum shear strength increasement was 800% compared with initial value. After a series of test, the electric gradient and treatment time for application of electric fielld were 1V/cm and 6 days. In case of 2nd additives test, the concentration for maximum shear strength is 250mM in all additives and the effects of shear strength improvement was developed approximately 20~30% in comparison to addition of single injection material.