한국소음진동공학회논문집 (Transactions of the Korean Society for Noise and Vibration Engineering)

  • 제16권12호
  • /
  • Pages.1272-1278
  • /
  • 2006
  • /
  • 1598-2785(pISSN)
  • /
  • 2287-5476(eISSN)
한국소음진동공학회 (The Korean Society for Noise and Vibration Engineering)
권호 표지
DOI QR코드

DOI QR Code

기판접합기술을 이용한 MEMS 컨덴서 마이크로폰의 설계와 제작

Design and Fabrication of MEMS Condenser Microphone Using Wafer Bonding Technology

  • 권휴상 (한국표준과학연구원 기반표준부 역학그룹) ;
  • 이광철 (한국표준과학연구원 전력기술연구부 미래신수요측정클럽)
  • 발행 : 2006.12.20
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents a novel MEMS condenser microphone with rigid backplate to enhance acoustic characteristics. The MEMS condenser microphone consists of membrane and backplate chips which are bonded together by gold-tin(Au/Sn) eutectic solder bonding. The membrane chip has $2.5mm{\times}2.5mm$, 0.5${\mu}m$ thick low stress silicon nitride membrane, $2mm{\times}2mm$ Au/Ni/Cr membrane electrode, and 3${\mu}m$ thick Au/Sn layer. The backplate chip has $2mm{\times}2mm$, 150${\mu}m$ thick single crystal silicon rigid backplate, $1.8mm{\times}1.8mm$ backplate electrode, and air gap, which is fabricated by bulk micromachining and silicon deep reactive ion etching. Slots and $50{\sim}60{\mu}m$ radius circular acoustic holes to reduce air damping are also formed in the backplate chip. The fabricated microphone sensitivity is 39.8 ${\mu}V/Pa$(-88 dB re. 1 V/Pa) at 1 kHz and 28 V polarization voltage. The microphone shows flat frequency response within 1 dB between 20 Hz and 5 kHz.

키워드

참고문헌

  1. Ono, N., Arita, T., Senjo, Y. and Ando, S., 2005, 'Directivity Steering Principle for Biomimicry Silicon Microphone', Transducers' 05, pp, 792-795
  2. Neumann Jr. J. J. and Gabriel, K. J., 2003, 'A Fully-integrated CMOS-MEMS Audio Microphone' , Transducers' 03, pp.230-233
  3. Schafer, D., Shoaf, S. and Loeppert, P., 1998, 'Micromachined Condenser Microhpone for Hearing Aid Use', Solid-state Sensor and Actuator Workshop (Hilton Head' 98), pp.27-30
  4. See, for example, http://www.knowlesacoustics.com/ or http://www.sonion.com/
  5. Hsieh, W. H., Yao, T.-J. and Tai, Y.-C., 1999, 'A High Performance MEMS Thin-film Teflon Electret Microphone', Transducers' 99, pp. 1064-1067
  6. Martin, D. T, Kadirvel, K, Liu, J., Fox, R. M., Sheplak, M. and Nishida, T., 2005, 'Surface and Bulk Micromachined Dual Back-plate Condenser Microphone', MEMS' 05, pp. 319-322
  7. Weigold, J. W., Brosnihan, T. J., Bergeron, J. and Zhang, X., 2006, 'A MEMS Condenser Microphone for Consumer Applications' , MEMS' 06, pp.86-89
  8. Ko, S. C., Jun, C.-H., Jang, W. I., Moon, S.-H., Hwang, G. and Choi, C. A., 2005, 'Fabrication and Acoustic Characteristics of Capacitive-MEMS Acoustic Sensor', The 7th Korean MEMS Conference, pp.81-84
  9. Lee, K. I., Cho, J. W., Lee, D. S., Hwang, H.-I., Kim, J. W. and Lee, S. S., 2005, 'A Capacitive Type Miniature Acoustic Transducer with a Diapragm by Electroplating' , The 7th Korean MEMS Conference, pp. 93-96
  10. Scheeper, P. R., Nordstrand, B., Gullov, J. O., Liu, B., Clausen, T., Midjord, L. and Storgaard-Larsen, T., 2003, 'A New Measurement Microphone Based on MEMS Technology', J. Microelectromech. Syst., Vol. 12, No.6, pp. 880-891 https://doi.org/10.1109/JMEMS.2003.820260
  11. Iguchi, Y., Tajima, T., Goto, M., Iwaki, M., Ando, A., Tanioka, K., Takeshi, F., Matsunaga, S. and Yasuno, Y., 2004, 'New Fabrication Process for High-performance Silicon Condenser Microphone with Monocrystalline Silicon Diaphragm and Backplate' , MEMS' 04, pp.601-604
  12. Wong, G. S. K. and Embleton, T. F. W., 1995, Handbook of Condenser Microphones, AlP Press, New York, Chap.3, pp.37-69
  13. Microphone Handbook, 1996, Bruel & Kjaer A/S, Naerum, Denmark
  14. Kinsler, L. E., Frey, A. R., Coppens, A. B., and Sanders, J. V., 2000, 'Fundamentals of Acoustics' , John Wiley & Sons, Inc., Chap.4, pp. 91-109
  15. Maier-Schneider, D., Maibach, J. and Obermeier, E., 1995, 'A New Analytical Solution for the Load-deflection of Square Membranes'. J. Microelectromech. Syst., Vol. 4, No.4, pp. 238-241 https://doi.org/10.1109/84.475551