참고문헌
- Dally, J. W., 1990, Packaging of Electronic System A Mechanical Engineering Approach, McGraw-Hill, Inc., New York
- Bar-Cohen, A., 1997, 'Air-Cooled Heat Sinks-Trends and Future Directions,' Proc. Advances in Electronic Packaging, Vol. 2, pp. 1827-1828
- Wood, A. S., Tupholme, G. E., Bhatti, M. I. H. and Heggs, P. J., 1995, 'Steady-State Heat Transfer Through Extended Plane Surfaces,' Int. Communications in Heat and Mass Transfer, Vol. 22, No.1, pp. 99-109 https://doi.org/10.1016/0735-1933(94)00056-Q
- Kadle, D. S. and Sparrow, E. M., 1986, 'Numerical and Experimental Study of Turbulent Heat Transfer and Fluid Flow in Longitudinal Fin Arrays,' Trans. ASME J. of Heat Transfer, Vol. 108, pp. 16-23 https://doi.org/10.1115/1.3246883
- Biber, C. R. and Belady, C. L., 1997, 'Pressure Drop Prediction for Heat Sinks: What is the Best Method,' Trans. ASME Proc. of the Advances in Electronic Packaging, Vol. 2, pp. 1829-1835
- Copeland, D., 2000, 'Optimization of Parallel Plate Heatsinks for Forced Convection,' 16th Annual IEEE Semiconductor Thermal Measurement and Management Symposium, pp. 266-272 https://doi.org/10.1109/STHERM.2000.837093
- Kang, H. S., 2001, 'Optimization of a 3-D Theramally Asymmetric Rectangular Fin,' KSME International Journal, Vol. 15, No. 11, pp. 1541-1547
- Kays, W. M. and London, A. L., 1964, Compact Heat Exchangers, MsGraw-Hill Co., New York
- Jonsson, H. and Palm, B., 2000, 'Thermal and Hydraulic Behavior of Plate Fin and Strip Fin Heat Sinks Under Varying Bypass Conditions,' IEEE Trans. on Component and Packaging Technologies, Vol. 23, No.1, pp. 47-54 https://doi.org/10.1109/6144.833041
- Shaukatullah, H., Storr, R. W., Hansen, J. B. and Gaynes, A. M., 1996, 'Design and Optimization of Pin Fin Heat Sinks for Low Velocity Applications,' IEEE Trans. on Components, Packaging, and Manufacturing Technology-Part A, Vol. 19, No. 5, pp. 486-494 https://doi.org/10.1109/95.554929
- Sara, O. N., 2003, 'Performance Analysis of Rectangular Ducts with Staggered Square Pin Fins,' Energy Conversion and Management, Vol. 44, No. 11, pp. 1787-1803 https://doi.org/10.1016/S0196-8904(02)00185-1
- Lee, S., 1995, 'Optimum Design and Selection of Heat Sinks,' IEEE Trans. on Component, Packaging and Manufacturing Technologies, Part A, Vol. 18, No.4, pp. 812-817 https://doi.org/10.1109/95.477468
- Ledezma, G., Morega, A. M. and Bejan, A., 1996, 'Optimal Spacing Between Pin Fins With Impinging Flow,' Trans. ASME J. of Heat Transfer, Vol. 118, pp. 570-577 https://doi.org/10.1115/1.2822670
- Cho, Y. J., Choi, C. H., Kim, J. J. and Lee, J. H., 2001, 'Optimum Design of Microchannel Heat Sinks,' Trans. of the KSME B, Vol. 25, No. 1, pp. 117-123
- Yovanovich, M. M., 1994, 'Heat Transfer in Electronic Packaging,' 10th Int. Heat Transfer Conference, Vol. 1, pp. 93-104
- Behm, J. and Huttunen, J., 2001, 'Heat Spreading and Conduction in Compressed Heat Sinks,' 10th Int. Flotherm User Conference, pp. 1-38
- Moffat, R. J., 1988, 'Describing the Uncertainties in Experimental Results,' Experimental Thermal and Fluid Science, Vol. 1, pp. 3-17 https://doi.org/10.1016/0894-1777(88)90043-X
- Jonsson, H. and Moshfegh, B., 2001, 'Modeling of the Thermal and Hydraulic Performance of Plate Fin, Strip Fin, and Pin Fin Heat Sinks - Influence of Flow Bypass,' IEEE Trans. on Component and Packaging Technologies, Vol. 24, No.2, pp. 142-149 https://doi.org/10.1109/6144.926376
피인용 문헌
- Effects of Symmetrically Arranged Heat Sources on the Heat Release Performance of Extruded-Type Heat Sinks vol.40, pp.2, 2016, https://doi.org/10.3795/KSME-B.2016.40.2.119
- Perfonnance Evaluation of Swaged- and Extruded-type Heat Sinks Used in Inverter for Solar Power Generation vol.37, pp.10, 2013, https://doi.org/10.3795/KSME-B.2013.37.10.933