The Effects of Thermocycling on the Shear Bond Strength between Metal Denture Base and Relining Resin

Thermocycling이 첨상용 레진과 금속 의치상간의 전단결합강도에 미치는 영향

  • Lee, Joon-seok (Dept. of Prosthodontics, College of Dentistry, Dankook University)
  • 이준석 (단국대학교 치과대학 치과보철학교실)
  • Published : 2005.11.30

Abstract

Purpose: Recently, various metal primers have been developed, and these are known to increase the bond strength between metal and relining resin. In this study, the change in bond strength according to amount of thermocycling was evaluated. Materials and Methods: In this study, 216 specimens were fabricated. Tokuyama Rebase $II^{(R)}$(Tokuyama Corp., Japan) and $Kooliner^{(R)}$(GC America Inc., Japan) as relining material, and MR. $Bond^{(R)}$(Tokuyama Corp., Japan) and Alloy $Primer^{(R)}$(Kuraray Medical Inc., Japan) as a metal primers were used. Using Ni-Cr and various metal surface treatment methods, resin was bonded and the change in bond strength during thermocycling was measured. The data was analyzed by one-way ANOVA, t-test(p<.05 level of significance). Results: When comparing the groups with only sandblasting, rapid decrease in shear bond strength could be seen. In the groups using Tokuyama Rebase $II^{(R)}$, with the exception of the 1000 and 2000 cycle groups, each group showed statistically significant decrease in shear bond strength(p<0.05). In comparison according to relining materials, $Kooliner^{(R)}$ showed higher shear bond strength than Tokuyama Rebase $II^{(R)}$ in all groups. In groups using MR $bond^{(R)}$, $Kooliner^{(R)}$ had higher shear bond strength than Tokuyama Rebase $II^{(R)}$ but, there was no statistical significance(p<0.05). In the other groups, $Kooliner^{(R)}$ showed significantly higher shear bond strength(p<0.05). There was significant difference between groups with sandblasting and metal primer treatments(p<0.05). In comparison according to metal primer materials, Alloy $Primer^{(R)}$ showed the highest shear bond strength but there was no statistical significance(p>0.05). According to the number of thermocycling cycles, when using Tokuyama Rebase $II^{(R)}$, there were no significant differences between the 0, 1000 and 2000 cycle groups regardless of the type of metal primer. There were no differences between the 2000 and 3000 cycle groups. When using $Kooliner^{(R)}$, regardless of the type of metal primer, there were no significant differences between the 0, 1000, 2000 and 3000 cycle groups(p>0.05). Conclusion: The use of metal primers showed increase in bond strength, and the stability after to thermocycling has been authenticated. Thus, the use of metal primers in relining and rebasing of metal frameworks is essential. But when selecting the material various physical properties should be considered.

Keywords

References

  1. Zarb GA, Bolender CL, Hickey JC, Carlsson GE. Boucher's Prosthodontic Treatment for Edentulous Patients. 10th ed. CV Mosby. 1990. p577-586
  2. Jeong CM. Atlas of Chairside Relining Technique. Shinhung International Inc. 2001. p13-22
  3. Renner RP, Boucher LJ, Removable Partial Dentures. Quintessence Publishing Co. Inc., 1987. p108-110
  4. McGivney GP, Castleberry DJ. McCraken's Removable Partial Prosthodontics. 9th ed. CV Mosby. 1995. p141-144
  5. NaBadalung DP, Powers JM, Connelly ME. Comparison of bond strength of three denture base resins to treated nickel-chromium-beryllium alloy. J Prosthet Dent 1998;80:354-361 https://doi.org/10.1016/S0022-3913(98)70137-4
  6. Jacobson TE, Chang JC, Ken PP, Watanabe LG. Bond strength of 4-META acrylic resin denture base to cobalt chromium alloy. J Prosthet Dent 1988;60:570-576 https://doi.org/10.1016/0022-3913(88)90216-8
  7. Tanaka T, Fujiyama E, Shimizu H et al. Surface treatment of nonprecious alloys for adhesion-fixed partial dentures. J Prosthet Dent 1986;55:456-462 https://doi.org/10.1016/0022-3913(86)90176-9
  8. Livaditis GJ. A chemical etching system for creating micromechanical retention in resin-bonded retainers. J Prosthet Dent 1986;56:181-188 https://doi.org/10.1016/0022-3913(86)90468-3
  9. Krueger GE, Diaz-Arnold, Aquilino SA, Scandrett FR. A comparison of electrolytic and chemical etch systems on the resin-to-metal tensile bond strength. J Prosthet Dent 1990;64:610-617 https://doi.org/10.1016/0022-3913(90)90137-2
  10. Zurasky JE, Duke ES. Improved adhesion of denture acrylic resins to base metal alloys. J Prosthet Dent 1987;57:520-524 https://doi.org/10.1016/0022-3913(87)90028-X
  11. Livaditis GJ, Thompson VP. Etched castings: An improved retentive mechanism for resin-bonded retainers. J Prosthet Dent 1982;47:52-58 https://doi.org/10.1016/0022-3913(82)90242-6
  12. Tanaka T, Atsuta M, Nakabayashi N, Masuhara E. Surface treatment of gold alloys for adhesion. J Prosthet Dent 1988;60:271-279 https://doi.org/10.1016/0022-3913(88)90267-3
  13. Watanabe F, Powers JM, Lorey RE. In vitro bonding of prosthodontic adhesives to dental alloys. J Dent Res 1988;67:479-483 https://doi.org/10.1177/00220345880670020901
  14. Hero H, Ruyter IE, Waarli ML, Hultquist G. Adhesion of Resins to Ag-Pd Alloys by Means of the Silicoating Technique. J Dent Res 1987;66:1380-1385 https://doi.org/10.1177/00220345870660081901
  15. Laufer BZ, Nicholls JI, Townsend JD. SiOx-C Coating: A composite-to-metal bonding mechanism. J Prosthet Dent 1988;60: 320-327 https://doi.org/10.1016/0022-3913(88)90277-6
  16. Munsil R, Tiller HJ. The adhesion of dental resins to metal surfaces. The silicoater technique, 1th ed., Kulzer & Co. GmbH, Wehrheim, 1984.p1-5
  17. Tanaka T, Hirano M, Kawahara M et al. A New Ion-coating surface treatment of alloys for dental adhesive resins. J Dent Res 1988;67:1376-1380 https://doi.org/10.1177/00220345880670110301
  18. Matsumura H, Kawahara M, Tanaka T, Atsuta M. Surface preparations for metal frameworks of composite resin veneered prostheses made with an adhesive opaque resin. J Prosthet Dent 1991;66: 10-15 https://doi.org/10.1016/0022-3913(91)90343-U
  19. Watanabe I, Matsumura H, Atsuta M. Effect of two metal primers on adhesive bonding with type IV gold alloys. J Prosthet Dent 1995;73:299-303 https://doi.org/10.1016/S0022-3913(05)80277-X
  20. Matsumura H, Shimoe S, Nagano K, Atsuta M. Effect of noble metal conditioners on bonding between prosthetic composite material and silver-palladiumcoppergold alloy. J Prosthet Dent 1999;81:710-714 https://doi.org/10.1016/S0022-3913(99)70111-3
  21. Matsumura H, Tanaka T, Taira Y, Atsuta M. Bonding of a cobalt-chromium alloy with acidic primers and tri-n-butylborane-initiated luting agents. J Prosthet Dent 1996;76:194-199 https://doi.org/10.1016/S0022-3913(96)90306-6
  22. Yoshida K, Taira Y, Sawase T, Atsuta M. Effects of adhesive primers on bond strength of self-curing resin to cobaltchromium alloy. J Prosthet Dent 1997;77:617-620 https://doi.org/10.1016/S0022-3913(97)70104-5
  23. Ohkubo C, Watanabe I, Hosoi T, Okabe T. Shear bond strengths of polymethyl methacrylate to cast titanium and cobaltchromium frameworks using five metal primers. J Prosthet Dent 2000;83:50-57 https://doi.org/10.1016/S0022-3913(00)70088-6
  24. Lee JS, Lim JH, Cho IH. A study on the tensile strength between metal denture base and relining materials. J Korean Acad Prosthodont 2000;38:1-11
  25. Kim YI, Jeong CM, Jeon YC. Effects of metal surface treatment on the shear bond strength between Ni-Cr denture base and reline resins. J Korean Acad Prosthodont 2002;40:396-404
  26. Choi NJ, Yang MS. The effects of metal surface treatment on bond strength between resin and metal interface of resin veneered crown. J Korean Acad Prosthodont. 1994; 32(4): 471-493
  27. Yim HS, Heo SJ, Cho IH. Comparison of retentive force of repair resin by various surface treatment methods in the repair of fractured porcelain fused to metal crown. J Korean Acad Prosthodont. 1992; 30(1)
  28. Matsumura H, Shimoe S, Nagano K, Atsuta M. Surface preparations for metal frameworks of composite resin veneered prostheses made with an adhesive opaque resin. J Prosthet Dent 1991;66:10-15 https://doi.org/10.1016/0022-3913(91)90343-U
  29. Matsumura H, Tanaka T, Taira Y, Atsuta M. Bonding of a cobalt-chromium alloy with acidic primers and tri-n-butylborane-initiated luting agent. J Prosthet Dent 1996;76:194-199 https://doi.org/10.1016/S0022-3913(96)90306-6
  30. Taira Y, Yoshida K, Matsumura H, Atsuta M. Phosphate and thiophosphate primers for bonding proshodontic luting materials to titanium. J Prosthet Dent 1998;79: 384-388 https://doi.org/10.1016/S0022-3913(98)70149-0
  31. Lee SY, Yang MS. The effects of thermocycling on the and strength between cobalt-chromium alloy and denture base resin. J Korean Acad Prosthodont. 2000; 38(1): 38-49
  32. Nelson RJ, Wolcott RB, Paffenarger GC. Fluid exchange at the margin of dental restorations. J Am Dent Assoc 1952;44:288-295 https://doi.org/10.1016/S0002-8177(52)43006-8
  33. Peterson EA, Philips RW, Swartz ML. A comparison of the physical properties of four restorative resins. J Am Dent Assoc 1966;73:1324-1336 https://doi.org/10.14219/jada.archive.1966.0352
  34. Moody CR, Dewald JP, Ferracane JL. Comparative study of luting agent with composite resin cores. J Prosthet Dent 1989;62:527-529 https://doi.org/10.1016/0022-3913(89)90072-3
  35. Arena CA, Evans DB, Hilton TJ. A comparison of bond strengths among chairside hard reline materials. J Prosthet Dent. 1993 Aug; 70(2): 126-131 https://doi.org/10.1016/0022-3913(93)90006-A
  36. Barkmeier WW, Latta MA. Laboratory evaluation of a metal-priming agent for adhesive bonding. Quintessence Int. 2000 Nov-Dec; 31(10): 749-752
  37. Ishijima T, Caputo AA, Mito R. Adhesion of resin to casting alloys. J Prosthet Dent. 1992 Apr; 67(4): 445-449 https://doi.org/10.1016/0022-3913(92)90070-Q
  38. Ryu YR, Lim JH, Cho IH. A study on the shear bond strength between nonprecious metal surface and resin cement according to the various surface treatment methods. J Korean Acad Prosthodont. 2001; 39(2): 157-170