Korean Journal of Food Science and Technology (한국식품과학회지)

Korean Society of Food Science and Technology (한국식품과학회)
권호 표지

Characteristics of Cereals Prepared by Extrusion-Cooking and Freeze-drying

압출성형과 동결건조 곡류의 특성

  • Tie, Jin (Department of Food Science and Technology, Kongju National University, Institute of Food Science, Kongju National University) ;
  • Park, Hee-Yong (Department of Food Science and Technology, Kongju National University, Institute of Food Science, Kongju National University) ;
  • Ryu, Gi-Hyung (Department of Food Science and Technology, Kongju National University, Institute of Food Science, Kongju National University)
  • 김철 (공주대학교 식품공학과, 공주대학교 식품과학연구소) ;
  • 박희용 (공주대학교 식품공학과, 공주대학교 식품과학연구소) ;
  • 류기형 (공주대학교 식품공학과, 공주대학교 식품과학연구소)
  • Published : 2005.10.31
Download PDF
⟨ Previous Next ⟩

Abstract

Characteristics of cereals prepared by extrusion-cooking and freeze-drying were compared. Parameters used were water solubility index (WSI), water absorption index (WAI), paste viscosity, and sterilization. Variables for extrusion process were barrel temperature at die section (70, 90, and $110^{\circ}C$) and moisture content (25 and 30%). WAI and WSI of extruded cereals were higher, whereas trough, breakdown, and final viscosity were lower than those of raw and freeze-dried cereals. Plate counting revealed no microbes in extruded cereals, whereas microbe colony was observed in freeze-dried cereals. Extrusion-cooking at low temperature resulted in better sterilization of microbes than freeze-drying for preparation of instant cereal drinks.

압출성형공정을 곡류식품 소재개발에 적용하기 위한 기초연구로서 압출성형으로 곡류를 처리한 후 압출성형 곡류, 원료 곡류, 동결건조 곡류의 수용성지수, 수분흡착지수, 페이스트점도와 미생물지표로서 일반세균수를 측정하였다. 압출성형 시료는 배럴온도(70, 90, $110^{\circ}C$)와 수분함량(25, 30%)을 달리하여 제조하였다. 원료 곡류, 동결건조 곡류, 압출성형 단일곡류와 압출성형 혼합곡류의 수용성지수와 수분흡착지수는 압출성형시료가 원료곡류와 동결건조 곡류에 비해 증가하였다. 압출성형 혼합곡류에서 수분용해지수는 배럴온도 $70^{\circ}C$, 수분함량 25%일 때 가장 높았고 수분흡착지수는 배럴온도 $110^{\circ}C$, 수분함량 25%일 때 가장 높게 나타났다. 원료 곡류, 동결건조 곡류, 압출성형 단일곡류와 압출성형 혼합곡류의 최고점도, 최저점도, 구조파괴점도, 최종점도는 압출성형시료가 원료 곡류와 동결건조 곡류에 비해 현저히 감소하였다. 압출성형 혼합곡류에서 최고점도와 구조파괴점도는 배럴온도 $70^{\circ}C$, 수분함량 25%일 때 가장 낮았고 최저점도는 배럴온도 $110^{\circ}C$, 수분함량 25%일 때 가장 낮은 값을 나타내었다. 최종점도는 배럴온도 $90^{\circ}C$, 수분함량 25%일 때 가장 낮게 나타났다. 미생물지표로서 일반세균수를 측정한 결과는 압출성형 공정으로 처리한 원료곡류와 혼합곡류에서 미생물이 검출되지 않았다.

Keywords

References

  1. Park MH. Current status and views of saengsik industry in Korea. Food Ind. Nutr. 7: 1-3 (2002)
  2. Lee SY. Processing unit operation of commercial saengsik. Food Ind. Nutr. 7: 11-15 (2002)
  3. Chung SS, Han YS. Consumer's recognition, nutrient composition and safety evaluation of commercial sunsik and saengsik. Korean J. Food Cult. 18: 235-243 (2003)
  4. Rauwendaal C. Polymer extrusion. Hanser Publishers, New York, USA. pp. 20-55 (1986)
  5. Harper JM. Extrusion of Foods. CRC Press Inc, Boca Raton, FL, USA. pp. 3-6 (1981)
  6. Ryu GH. Red ginseng products and its process. Food Ind. Nutr. 8: 38-42 (2003)
  7. Meuser F, Wiedmann W. 1989. Extrusion plant design. pp. 91-155. In: Extrusion Cooking. Mercier C, Linko P, Harper JM (eds). AACC, St. Paul, MN, USA (1989)
  8. Ryu GH, Neumann PE, Walker CE. 1994. Effects of emulsifiers on physical properties of wheat flour extrudates with/without sucrose and shortening. Lebensm. Wiss. Technol. 27: 425-431 (1994) https://doi.org/10.1006/fstl.1994.1088
  9. Ryu GH, Walker CE. Cell structure of wheat flour extrudates properties produced with various emulsifiers. Lebensm. Wiss. Technol. 21: 432-436 (1994)
  10. Ryu GH, Walker CE. The effects of extrusion conditions on the physical properties of wheat flour extrudate. Starch/Starke 47: 3336 (1995)
  11. Ryu GH, Ng PKW. Effects of selected process parameters on expansion and mechanical properties of wheat flour and whole cornmeal extrudates. Starch/Starke 53: 147-154 (2001) https://doi.org/10.1002/1521-379X(200104)53:3/4<147::AID-STAR147>3.0.CO;2-V
  12. Ryu GH, Mulvaney SJ. Cornmeal puffing with CO2 gas: Effect of sucrose and glyceryl monostearate(GMS). Korean Food Sci. Technol. 27: 251.256 (1996)
  13. Ryu GH, Lee EY, Lim ST. Physical properties and process optimization of corn starch extrudates expanded with supercritical carbon dioxide injection. Cereal Chem. 76: 63-69 (1999) https://doi.org/10.1094/CCHEM.1999.76.1.63
  14. Kang SH, Ryu GH. Improvement in the Yukwa manufacturing by extrusion process with $CO_2$ gas injection. Food Sci. Biotechnol. 10: 1-6 (2001)
  15. Ryu GH, Kim BS, Mulvaney SJ. Optimization of extrusion process for dairy ingredient fortification of cornmeal puffed via $CO_2$ gas injection. Food Biotechnol. 11: 552-556 (2002)
  16. Ryu GH. Texturization of plant protein by using extrusion process. Food Eng. Prog. 2: 73-79 (2003)
  17. Chang YS. Extrudate characteristics for developing sunsik process by extrusion-cooking. MS thesis, Kongju National University, Yesan, Korea (2004)
  18. AACC. Approved Method of the AACC. American Association of Cereal Chemists. St. Paul, MN, USA (1983)
  19. RVA Manual. RVA-3 series operation manual using Dos thermocline software. Newport Scientific (1995)
  20. Chinnaswamy R, Hanna MA. Macromolecular and functional properties of native and extrusion cooked corn starch. Cereal Chem. 6: 490 (1990)
  21. Jackon DS, Gomez MH, Waniska RD, Rooney LW. Effects of single-screw extrusion cooking on starch as measured by aqueoushigh-performance size-exclusion chromatography. Cereal Chem. 67: 529 (1990)
  22. EL-Dash AA, Gonzaless R, Ciol M. Response surface methodology in the control of thermoplastic extrusion of starch. pp. 51-74. In: Extrusion Cooking Technology. Jowitt R (ed). Elsevier Applied Science Publishers, New York, USA (1980)
  23. Bhattachatya S, Sudba ML, Rahim A. 1999. Pasting characteristics of an extruded blend of potato and wheat flours. J. Food Eng. 40: 107-111 (1999) https://doi.org/10.1016/S0260-8774(99)00046-1
  24. Ryu, GC. Effect of melt moisture and post-extrusion variables on pasting and thermal properties of corn starch extrudates. MS thesis, Kongju National University, Yesan, Korea (2002)
  25. Grant LA. Effect of starch isolation, drying and grinding techniques on its gelatinization and retrogradation properties. Cereal Chem. 75: 590-594 (1998) https://doi.org/10.1094/CCHEM.1998.75.5.590
  26. Noguchi A. Principle of twin-screw extruder and application for food process. pp. 100-104. In: Food Extrusion Technology (II). Lee CH, Kim JB, Han O, Lim JK, Noguchi A, Hayakawa I, Isobe A, Oda Y (eds). Yulim Publishing, Korea (1995)
  27. Hayakawa I. Enzyme inactivation and sterilization by using extrusion process. pp. 147-159. In: Food Extrusion Technology (II). Lee CH, Kim JB, Han O, Lim JK, Noguchi A, Hayakawa I, Isobe A, Oda Y (eds). Yulim Publishing, Korea (1995)