Wind and Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Stability analysis of truss type highway sign support structures

  • Yang, Jun (Department of Civil & Environmental Engineering, University of Connecticut) ;
  • Culmo, Michael P. (CME Associates) ;
  • Dewolf, John T. (Department of Civil & Environmental Engineering, University of Connecticut)
  • Received : 2003.09.05
  • Accepted : 2004.10.08
  • Published : 2004.12.25
⟨ Previous Next ⟩

Abstract

The design of truss type sign support structures is based on the guidelines provided by the American Association of State Highway and Transportation Officials Standard Specifications for Highway Signs, Luminaries and Traffic Signals and the American Institute of Steel Construction Design Specifications. Using these specifications, the column design strength is normally determined using the effective length approach. This approach does not always accurately address all issues associated with frame stability, including the actual end conditions of the individual members, variations of the loads in the members, and the resulting sidesway buckling for truss type sign support structures. This paper provides insight into the problems with the simplified design approach for determining the effective lengths and discusses different approaches for overcoming these simplifications. A system buckling approach, also known as a rational buckling analysis, is used in this study to determine improved predictions for design strength of truss type sign support structures.

Keywords

References

  1. Alampalli, S. (1997), "Wind loads on untethered-span-wire traffic-signal poles", Report FHWA/NY/SR-97/126,Transportation Research and Development bureau, New York State Department of Transportation.
  2. American Association of State Highway and Transportation Officials (1998), "Standard specifications forstructural supports for highway signs, luminaries, and traffic signals", AASHTO, Washington, D. C.
  3. American Association of State Highway and Transportation Officials (1994), "Standard specifications forstructural supports for highway signs, luminaries, and traffic signals", AASHTO, Washington, D. C.
  4. American Institute of Steel Construction (1994), "Manual of steel construction - load & resistance factor design",Second edition, American Institute of Steel Construction, Inc., Chicago, IL.
  5. American Society of Civil Engineers (1997), "Effective length and notional load approaches for assessing framestability: implications for american steel design", Task Committee on Effective Length, ASCE, New York, NY.
  6. Chajes, A. (1974), Principles of Structural Stability Theory, Englewood Cliffs, N. J., Prentice-Hall.
  7. Chen, W.F. and Lui, E.M. (1987), Structural Stability: Theory and Implementation, Elseiver Science PublishingCo., Inc., New York, NY.
  8. Cook, R.A., Bloomquist, D. and Kalajian, M.A. (1999), "Mechanical damping system for mast arm traffic signalstructure", Proc. of the 1999 Structures Congress: Structural Engineering in The 21st Century, April 18-21,1999, New Orleans, Louisiana, pp. 1099-1102.
  9. Cook, R.A., Bllomquist, D. and Agosta, A.M. (1997), "Truck-induced dynamic wind loads on variable-messageSigns", Transportation Research Record: No. 1594: Bridges, Other Structures, and Hydraulics and Hydrology,Transportation Research Board, Washington, D. C., pp. 187-193.
  10. DeWolf, J.T. and Yang, J. (2000), "Stability analysis of truss type highway sign support structures", Final Report,Project No. 97-2, Connecticut Depart of Transportation, Rocky Hill, Connecticut.
  11. Fouad, F.H., Calvert, E.A. and Nunez, E. (1998), "Structural supports for highway signs, luminaires, and trafficsignals", NCHRP Report 411, Transportation Research Board, National Research Council, Washington, D. C.
  12. Gray, B., Wang, P., Hamilton, H.R. and Puckett, J.A. (1999), "Traffic signal structure research at university ofwyoming", Proc. the 1999 Structures Congress: Structural Engineering in The 21st Century, April 18-21,1999, New Orleans, Louisiana, pp. 1107-1110.
  13. Hartnagel, B.A. and Barker, M.G. (1999), "Strain measurements on traffic signal mast arms", Proc. the 1999Structures Congress: Structural Engineering in The 21st Century, April 18-21, 1999, New Orleans, Louisiana,pp. 1111-1114.
  14. Hartz, B.J. (1965), "Matrix formulation of structural stability problems", Journal of the Structural Division, Proc.The American Society of Civil Engineers, 91(ST 6), Dec. 141-157.
  15. Horne, M.R. and Merchant, W. (1965), The Stability of Frames, First Edition, Pergamon Press Ltd., HeadingtonHill Hall, Oxford, England.
  16. Johns, K.W. and Dexter, R.J. (1999), "Truck-induced loads on highway sign support structures", Proc. the 1999Structures Congress: Structural Engineering in The 21st Century, April 18-21, 1999, New Orleans, Louisiana,pp. 1103-1106.
  17. Kaczinski, M.R., Dexter, R.J. and Van Dien, J.P. (1998), "Fatigue-resistant design of cantilevered signal, andlight supports", NCHRP Report 412, Transportation Research Board, National Research Council, Washington,D. C.
  18. Kashar, L., Nester, M.R., Jones, J.W., Hariri, M. and Friezner, S. (1999), "Analysis of the catastrophic failure ofthe support structure of a changeable message sign", Proc. the 1999 Structures Congress: StructuralEngineering in The 21st Century, April 18-21, New Orleans, Louisiana, pp. 1115-1118.
  19. White, D.W. and Hajjar, J.F. (1997a), "Buckling models and stability design of steel frames: a unified approach", J. Constr. Steel Res., 42(3), June, 171-207. https://doi.org/10.1016/S0143-974X(97)00014-X
  20. White, D.W. and Hajjar, J.F. (1997b), "Accuracy and simplicity of alternative procedures for stability design ofsteel frames", J. Constr. Steel Res., 42(3), June, 209-261. https://doi.org/10.1016/S0143-974X(97)00015-1