Journal of Mechanical Science and Technology

  • 제18권12호
  • /
  • Pages.2284-2293
  • /
  • 2004
  • /
  • 1738-494X(pISSN)
  • /
  • 1976-3824(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지

Evaporation Heat Transfer and Pressure Drop Characteristics of R-134a in the Oblong Shell and Plate Heat Exchanger

  • Park, Jae-Hong (Department of Refrigeration & Air-Conditioning Engineering, PuKyong National University) ;
  • Kim, Young-Soo (College of Engineering School of Mechanical aEngineering, PuKyong National University)
  • 발행 : 2004.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The evaporation heat transfer coefficient h$\_$r/ and frictional pressure drop Δp$\_$f/ of refrigerant R-134a flowing in the oblong shell and plate heat exchanger were investigated experimentally in this study. Four vertical counterflow channels were formed in the oblong shell and plate heat exchanger by four plates of geometry with a corrugated sinusoid shape of a 45 chevron angle. Upflow of refrigerant R-134a boils in two channels receiving heat from downflow of hot water in other channels. The effects of the refrigerant mass flux, average heat flux, refrigerant saturation temperature and vapor quality of R-134a were explored in detail. Similar to the case of a plate heat exchanger, even at a very low Reynolds number, the flow in the oblong shell and plate heat exchanger remains turbulent. The results indicate that the evaporation heat transfer coefficient h$\_$r/ and pressure drop Δp$\_$f/ increase with the vapor quality. A rise in the refrigerant mass flux causes an increase in the h$\_$r/ and Δp$\_$f/. But the effect of the average heat flux does not show significant effect on the h$\_$r/ and Δp$\_$f/. Finally, at a higher saturation temperature, both the h$\_$r/ and Δp$\_$f/ are found to be lower. The empirical correlations are also provided for the measured heat transfer coefficient and pressure drop in terms of the Nusselt number and friction factor.

키워드

참고문헌

  1. Akers, W. W., Dean, H. A. and Crosser, O., 1958, 'Condensation Heat Transfer Within Horizontal Tubes,' Chem. Eng. Prog., 54, pp. 89-90
  2. Farrell, P., Wert, K. and Webb, R., 1991, 'Heat Transfer and Friction Characteristics of Turbulent Radiator Tubes,' SAE Technical Paper series, No. 910197
  3. Kline, S. J. and McClintock, F. A., 1953, 'Describing Uncertainties in Single-sample Experiments,' Mechanical Engineering, Vol. 75, No. 1, pp. 3-12
  4. Shah, R. K. and Focke, W. W., 1988, 'Plate Heat Exchangers and Their Design Theory,' in : Shah, R. K., Subbarao, E. C., Mashelkar, R. A. (eds.), Heat Transfer Equipment Design, Hemisphere, Washington, DC, pp. 227-254
  5. Shah, R. K. and Wanniarachchi, A. S., 1992, 'Plate Heat Exchanger Design Theory in Industry Heat Exchanger,' in : J. M. Buchlin(eds.), Lecture Series, No, 1991-04, Von Karman Institute for Fluid Dynamics, Belgium
  6. Sieder, E. N. and Tate, G. E., 1936, 'Heat Transfer and Pressure Drop of Liquids in Tubes,' Int. Eng. Chem., Vol. 28, pp. 1429-1435 https://doi.org/10.1021/ie50324a027
  7. Wilson, E. E., 1915, 'A Basis for Rational Design of Heat Transfer Apparatus,' Trans. ASME, Vol. 37, pp. 47-70
  8. Yan, Y. -Y. and Lin, T. -F., 1999, 'Evaporation Heat Transfer and Pressure drop of Refrigerant R-134a in a Plate Heat Exchanger,' J. Heat Transfer, Vol. 121, pp. 118-127 https://doi.org/10.1115/1.2825924
  9. Zivi, S. M., 1964, 'Estimation of Steady State Void Fraction by means of the Principle of Minimum Entropy Production,' Trans. Am. Soc. Mech., Eng., Ser. C. J. Heat Transfer, Vol. 86, pp. 247-252 https://doi.org/10.1115/1.3687113