Corrosion Science and Technology

  • 제2권1호
  • /
  • Pages.36-40
  • /
  • 2003
  • /
  • 1598-6462(pISSN)
  • /
  • 2288-6524(eISSN)
한국부식방식학회 (The Corrosion Science Society of Korea)
권호 표지

Effect of Welding Processes on Corrosion Resistance of UNS S31803 Duplex Stainless Steel

  • Chiu, Liu-Ho (Department of Materials Engineering, Tatung University) ;
  • Hsieh, Wen-Chin (Department of Materials Engineering, Tatung University)
  • 발행 : 2003.02.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

An attractive combination of corrosion resistance and mechanical properties in the temperature range -50 to $250^{\circ}C$ is offered by duplex stainless steel. However, undesirable secondary precipitation phase such as $\sigma$, $\gamma_2$ and $Cr_2N$ may taken place at the cooling stage from the welding processes. Therefore, this paper describes the influence of different welding procedures such as manual metal arc welding (MMA), tungsten inert gas welding (TIG) and vacuum brazing on corrosion resistance of the welded joint for UNS S31803 duplex stainless steel. Microstructure and chemical compositions of the welded joint were examined. The weight loss of specimens immersed in 6% $FeCl_3$ solution at $47.5^{\circ}C$ for 24-hours was determined and used to evaluate the pitting resistance of duplex stainless steel and their welds. The region of heat-affected zone of specimen obtained by the MMA is much wider than that resulted from TIG, therefore, the weight loss of welds by MMA was larger than that of weld by TIG. The weight loss of brazed specimens cooled from slow cooling rate was larger than those of specimens cooled from high cooling rate, because the precipitation of $\sigma$ phase. Beside that, the weight loss of brazed specimen is greater than those of the welded specimens. The galvanic corrosion was observed in brazed duplex stainless steel joints in the chloride solution.

키워드

과제정보

연구 과제 주관 기관 : Tatung University

참고문헌

  1. R. A. Walker, Mater. Sci. Technol., 4, 78 (1988)
  2. J.-O. Nilsson, Mater. Sci. Technol., 8, 685 (1992)
  3. K. Bekkers, Welding in the World, 36, 111 (1995)
  4. L. Karlsson, S. Rigdal, and S. L. Andersson, Welding in the World, 39, 99 (1997)
  5. A. Dhooge and E. Deleu, Welding in the world, 39, 47 (1997)
  6. J. D. Kordatos,G. Fourlaris, and G. Papadimitriou, Scripta Mater., 44, 401 (2001)
  7. Y.-H. Park and Z.-H. Lee, Mater. Sci. Eng., A297, 78 (2001)
  8. C. E. Cross, H. Hoffmeister, and G. Huismann, Welding in the World, 39, 154 (1997)
  9. M. Schwartz, in Brazing: For the Engineering Technologist, Chapman & Hall, London, UK, 258 (1995)
  10. ASTM G48-92, Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution, (1992)
  11. J. H. Potgieter, British Corr. J., 27, 219 (1992)