한국주조공학회지 (Journal of Korea Foundry Society)

  • 제22권4호
  • /
  • Pages.174-183
  • /
  • 2002
  • /
  • 1598-706X(pISSN)
  • /
  • 2288-8381(eISSN)
한국주조공학회 (Korea Foundry Society)
권호 표지

쌍롤법에 의한 Al-Sn합금 Strip의 제조 및 특성에 관한 연구

A Stud on the Fabrication and Characteristics of Al-Sn Alloy Strips by Twin-Roll Process

  • 이정근 (인하대학교 재료공학부) ;
  • 주대헌 (인하대학교 재료공학부) ;
  • 김명호 (인하대학교 재료공학부)
  • Lee, Jeong-Keun (School of Materials Science and Engineering, Inha University) ;
  • Joo, Dae-Heon (School of Materials Science and Engineering, Inha University) ;
  • Kim, Myung-Ho (School of Materials Science and Engineering, Inha University)
  • 발행 : 2002.08.20
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Twin-roll process is a relatively new continuous casting process which can produce high-quality strip products directly, and solidification rate can reach $10^3$ to $10^4$ K/s, leading to fine and uniform microstructures with enhanced mechanical properties. The strip casting condition for producing fine Al-Sn alloy strip was obtained experimentally, and defects appearing on the strip was examined. Crack formation and surface quality of the strip was found to depend mainly on process parameters such as melt temperature, roller gap and rolling speed. Sn structure of network type was observed in Al-20Sn and Al-40Sn alloy strips, and cell spacing of Al-40Sn alloy was smaller than that of Al-20Sn. Banding strength of the heat treated specimens increased with increasing of soaking time and temperature, and bonding strength of Al-20Sn alloy was more superior than that of Al-40Sn alloy. However wear resistance of Al-40Sn alloy contained large amount of soft Sn which possess good anti-friction characteristics was superior than that of Al-20Sn alloy.

키워드

참고문헌

  1. Koushiyobou Sliding Bearing and Lubrication Mori Sou Nae
  2. J. Laser Applications v.9 Laser Cladding of Al-Sn Alloy on a Mild Steel Z. Liu;J. L. Sun;W. M. Steen;K. G. Watkins;C. Lee;W. P. Brown https://doi.org/10.2351/1.4745443
  3. Materials Science Forum v.331-337 Production of Ultrafine Microstructures in Al-Sn, Al-Sn-Cu and Al-Sn-Cu-Si Alloys for Use in Tribological applications S. J. Harris;D. G. McCartney;A. J. Horlock;C. Perrin https://doi.org/10.4028/www.scientific.net/MSF.331-337.519
  4. J. Alloys and Compounds v.215 Electron Microscopy Characterization of Al-Sn Metal-metal Matrix Composites S. Abis;G. Barucca;P. Mengucci https://doi.org/10.1016/0925-8388(94)90859-1
  5. Metal Progress Improved Aluminum Bearings (Al-Sn and Al-Sn-Cu Alloys) H. K. Hardy;E. A. G. Liddiard;J. Y. Higgs;J. W. Cuthbertson
  6. Tribology Development of a High-tin Aluminum Plain Bearing Material M. P. E. Desvaux
  7. J. Kor. Inst. Met. & Mater. v.21 Structure and Wear Properties of Al-Sn Alloy Produced by Electroslag Remelting Hoon Yung Yaung;Jin Il Choi;Ki Young Kim
  8. J. Jpn. Inst. Met. v.29 On the Structure of Unidirectionaly Solidified Al-Sn Alloys S. Nishi;T. Ikeda;T. Ohta;N. Udagawa https://doi.org/10.2464/jilm.29.519
  9. The 3rd International Conf. on Aluminum alloys Grain Refinement fo Twin-roll Cast Aluminum Alloys X. Yang;J. D. Hunt;D. V. Edmonds
  10. J. Kor. Fondrymen's Soc. v.10 The Occurence of Structure Inhomogeneities and Defects in As Cast Strip During Twin Roll Casting of Aluminum S. S. Cho
  11. SAE Tech. Paper 932903 A New Aluminum-Based Bearing Alloy for Slide Type Antifriction Bearings S. Abis;W. Benetti
  12. Acta Mater. v.46 An X-ray Study on the Mechanical Effects of the Peel Test in a Cu/Cr/Polyimide System I. S. Park;Jin Yu https://doi.org/10.1016/S1359-6454(97)00208-5
  13. Advanced technology of Plasticity v.2 Comparison of Molten metal and Mushy State Pouring in Direct Rolling Process Y. D. Kim;N. J. Baek;C. G. Kang
  14. Materials Science and Engineering v.A173 Microstructural Defects in High Productivity Twin-roll Casting of Aluminium D. J. Monaghan;M. B. Henderson;J. D. Hunt;D. V. Edmonds
  15. A Doctor's Thesis A Study on the Heat Flow and Microstructure in Rapid Solidification W. T. Kim