Steel and Composite Structures

  • 제2권4호
  • /
  • Pages.277-296
  • /
  • 2002
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Behavior and modeling of single bolt lap-plate connections

  • Rex, Clinton O. (Stanley D. Lindsey and Assoc., The Via Department of Civil and Environmental Engineering, Virginia Polytechnic Institute and State University) ;
  • Easterling, W. Samuel (Stanley D. Lindsey and Assoc., The Via Department of Civil and Environmental Engineering, Virginia Polytechnic Institute and State University)
  • 투고 : 2002.03.11
  • 심사 : 2002.08.05
  • 발행 : 2002.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

A research investigation of single bolt lap-plate connection load-deformation behavior is presented. Each important characteristic of this behavior is evaluated and two methods for analytically approximating the behavior are developed and presented. The first of these methods is a component method in which the behavior of the connection is modeled as a combination of the behavior of the parts. The second method utilizes a number of parametric relationships that relate the connection parameters to coefficients of two non-linear continuous analytical curves. The test results from four independent experimental programs that investigated the behavior of single bolt lap-plate connections are used in the development and verification of these methods.

키워드

참고문헌

  1. Caccavale, S. E. (1975). "Ductility of single plate framing connections," M. S. Thesis University of Arizona.
  2. Crawford, S. F. and Kulak, G. L. (1971). "Eccentrically loaded bolted connections," J. Struct. Div., 97(ST3), 765-783.
  3. Eurocode 3: Design of Steel Structures, Part 1.1 Revised Annex J Joints and Building Frames (1994) Commission of The European Communities.
  4. Fisher, J. W. (1965). "Behavior of fasteners and plates with holes," J. Struct. Div., 91(ST6), 265-286.
  5. Fisher, J. W. and Struik J. H. A. (1974). John Wiley & Sons, Guide to Design Criteria for Bolted and Riveted Joints.
  6. Fisher, J. W., Galambos, T. V., Kulak, G. L., and Ravindra, M. K. (1978) "Load and resistance factor design criteria for connectors," J. Struct. Div., 104(ST9), 1427-1441.
  7. Frank, K. H. and Yura, J. A. (1981). "An experimental study of bolted shear connections", Report No. FHWA/ RD-81/148, US. Department of Transportation, Federal Highway Administration.
  8. Gillett, P. E. (1978), "Ductility and strength of single plate connections," Ph.D. Dissertation, The University of Arizona.
  9. Karsu, B. (1995) "The load deformation response of single bolt connections," M. S. Thesis Virginia Polytechnic Institute and State University.
  10. Kulak, G. L., Fisher, J. W., and Struik, J. H. A. (1987). Guide to Design For Bolted and Riveted Joints, 2nd Edition, John Wiley & Sons, New York, NY, 1987.
  11. Load and Resistance Factor Design Specification for Structural Steel Buildings (1986). American Institute of Steel Construction, Chicago, Illinois.
  12. Load and Resistance Factor Design Specification for Structural Steel Buildings (1993). American Institute of Steel Construction, Chicago, Illinois.
  13. Manual of Steel Construction Volume I and II Load and Resistance Factor Design (1994). American Institute of Steel Construction, Chicago, Illinois.
  14. Munse, W. H., Wright, D. T., and Newmark, N. M. (1954) "Laboratory tests of high tensile bolted structural joints" Proceedings of ASCE, 80(441) May, 441-1 to 441-38.
  15. Perry, W. C. (1981). "The bearing strength of bolted connections," M. S. Thesis University of Texas at Austin.
  16. Rex, C. O. and Easterling, W. S. (1996a). "Behavior and modeling of a single plate bearing on a single bolt," Report CE/VPI-ST 96/14, Virginia Polytechnic Institute and State University, Blacksburg, VA.
  17. Rex, C. O. and Easterling, W. S. (1996b). "Behavior and modeling of single bolt lap plate connections," Report CE/VPI-ST 96/15, Virginia Polytechnic Institute and State University, Blacksburg, VA.
  18. Rex, C. O. and Easterling, W. S. (1996c). "Behavior and modeling of partially restrained steel beam-girder connections," Report CE/VPI-ST 96/16, Virginia Polytechnic Institute and State University, Blacksburg, VA.
  19. Rex, C. O. and Easterling, W. S. (2003). "Behavior and modeling of a single plate bearing on a single bolt," J. Struct. Eng., ASCE, to appear
  20. Richard, R. M. and Elsalti, M. K. (1991). "PRCONN, moment-rotation curves for partially restrained connections." Users manual for program developed at The University of Arizona Department of Civil Engineering and Engineering Mechanics.
  21. Sarkar, D. and Wallace, B. (1992). Design of Single Plate Framing Connections, DRAFT Report No. FSEL/AISC 92-01, Fears Structural Engineering Laboratory, University of Oklahoma.
  22. Simkins, T. E. (1967). "The mutuality of static and kinetic friction," Lubrication Engineering, American Society of Lubrication, Vol. 23 (21), 26-31.
  23. Wallaert, J. J. and Fisher, J. W. (1965). "The shear strength of high-strength bolts," J. Struct. Div., 91(ST3), 99-125.