DOI QR코드

DOI QR Code

Experimental Study for the Durability Enhancement of Plastic Spur Gear

플라스틱스퍼기어의 내구성향상에 관한 실험연구

  • 김충현 (한국과학기술연구원 트라이볼로지연구센터) ;
  • 안효석 (한국과학기술연구원 트라이볼로지연구센터) ;
  • 정태형
  • Published : 2002.09.01

Abstract

Operating test of power-transmission plastic spur gears were performed inspecting both characteristics of friction-wear and endurance, and suggesting endurance improvement method that either drills internal holes of tooth or inserts metallic pin in the internal hole of tooth and verifying this newly-provided method. In case of acetal gears, amount of friction-wear is observed to increase by development of plastic deformation and increase of tooth stiffness due to brittle material property of acetal. To the contrary, in case of nylon gears, suggested method is shown to drop down the tooth temperature for about 3∼10$^{\circ}C$ than original gear, thus amount of wear is reduced by over 30% and operating lift prolonged by more than 200%. Hence, suggested method is proved to be practically applicable to the plastic gears made by soft polymers such as Nylon.

Keywords

References

  1. Plastics Gearing : Selection and Application Adams C.E.
  2. Adams, C. E., 1986, Plastics Gearing ; Selection and Application, Marcel Dekker, Inc., New York
  3. Macdermott, C. P. and Shenoy, A. V., 1997, Selecting Thermoplastics for Engineering Application, 2nd Ed., Marcel Dekker, Inc., New York
  4. Maxwell, J., 1999, Plastics ; The Layman's Guide, The University Press, Cambridge
  5. Tsukamoto, N., 1979, 'Investigation about the Strength of Plastic Gears (1st. The Strength of Nylon Gears which have Counter-corwing),' Bulletin of the JSME, Vol. 22, No. 173, pp. 1685-1692 https://doi.org/10.1299/jsme1958.22.1685
  6. Tsukamoto, N., 1981, 'Investigation about the Strength of Plastic Gears (2nd report ; Abrasion of the Nylon Gear for Power Transmission, Meshing with the Steel Gear),' Bulletin of the JSME, Vol. 24, No. 191, pp. 872-881 https://doi.org/10.1299/jsme1958.24.872
  7. Tukamoto N., 1984, 'Investigation about Load Capacity of Nylon Gears, when Tooth Surface Finishing of Mating Steel Gears is Different (2nd Report ; Abrasion of Nylon Gear Meshing with Ground Steel Gera),' Bulletin of the JSME, Vol. 27, No. 229, pp. 1529-1536
  8. Terashima, K., Tsukamoto N., and Shi J., 1984, 'Development of Plastic Gears for Power Transmission (Power Transmission Mechanism of Plastic Gears),' Bulletin of the JSME, Vol. 27, No. 231, pp. 2061-2068 https://doi.org/10.1299/jsme1958.27.2061
  9. Terashima, K., Tsukamoto, N., and Nishida, N., 1986, 'Development of Plastic Gears for Power Transmission (Design on Load-Carrying Capacity),' Bulletin of the JSME, Vol. 29, No. 250, pp. 1326-1329 https://doi.org/10.1299/jsme1958.29.1326
  10. Terashima, K., Tsukamoto, N., and Nishida, N., 1986, 'Development of Plastic Gears for Power Transmission (Abnormal Wear near Tooth Root and Tooth Fracture near Pitch Point),' Bulletin of the JSME, Vol. 29, No. 251, pp. 1598-1604 https://doi.org/10.1299/jsme1958.29.1598
  11. Tsukamoto, N., Yano, T., Sakai, H., 'Noise and Transmission Efficiency under Deformation of Tooth Form of Nylon Gears,' Bulletin of the JSME, Vol. 25, No, 207, pp, 1465-1473
  12. Kim, Choong Hyun, Ahn, Hyo-Sok, and Chong Tae Hyong, 2000, 'Reciprocating Sliding Wear of Nylon and Polyacetal Against Steel,' Transactions of the KSME, A, Vol. 24, No.3, pp. 786-793
  13. Kim, Choong Hyun, Lee, Sung-Chul, Ahn, Hyo-Sok, and Chong, Tae Hyong, 2000, 'Wear and Operation Characteristics of Acetal and Nylon Pinion Against Steel Gear,' Transactions of the KSME, A, Vol. 24, No. 9, pp, 2387-2396
  14. Ahn, Tae-Wan, Lee, Dong-He, Park, Yee-Soon, Lee, Sang-Won, and Chong, Han-Mo, 1987, Physical Polymer Science, Daekwang Publishing Co., Ltd
  15. DuPont Engineering Polymers, 2000, 'General Principles for DuPont Engineering Polymers,' pp. 57-70
  16. Tsukamoto, N., Taki, T., and Nishida, N., 1987, 'A Study on Strength Design Methods of Plastic Gears,' Transactions of the JSME, C, Vol. 53, No. 486, pp. 432 -435
  17. Terashima, K., Tsukamoto, N., Nishida, T., and Seki, K., 1985, 'A Study on the Power Translation Plastic gears,' Transactions of the JSME, C, Vol. 51, No. 469, pp. 2309-2315 https://doi.org/10.1299/kikaic.51.2309
  18. Dudley, D. W., 1984, Handbook of Practical Gear Design, McGraw-Hill
  19. Colbourne, J. R., 1987, The Geometry of Involute Gears, Springer-Verlag
  20. Tsukamoto, N., Maruyama, H., and Mimura H.., 1985, 'Effect of Reducing Friction of Poly acetal in Gears,' Transactions of the JSME, C, Vol. 57, No. 533, pp. 230-235