Transactions of the Korean Society of Mechanical Engineers A (대한기계학회논문집A)

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지
DOI QR코드

DOI QR Code

A Study on Parameters Measured during Small Punch Creep Testing

소형펀치 크리프 시험중 측정하는 변수에 대한 연구

  • Published : 2002.01.01
Download PDF
⟨ Previous Next ⟩

Abstract

An effect is made in this study to deepen understanding of small punch(SP) creep testing which has been a round for about 10 years as a substitute for the conventional uniaxial creep testing. Even though considerable numbers of SP creep test program have been performed, most of the tests were aimed at measuring creep rupture lives only. Very flew studies showed interest on the meaning of what we were really measuring during the SP creep tests. In this paper meanings of the parameters measured during the SP creep testing, such as punch load and punch displacement rate are investigated using finite element analysis. It was shown that the measured parameters must represent the stress and strain rates of the material at the annular region located at about 0.65 mm from the center of the SP specimen. The material in this location would go through constant maximum stress and strain rate during the testing. Experimental verification is also discussed.

Keywords

References

  1. 윤봉기, 1992, '고온 사용설비 파손방지 기술개발,' 과학기술처 보고서, KRISS-92-88-IR
  2. 한상인, 정세희, 윤기봉, 1997, '입계부식법에 의한 사용중인 화력발전소 요소의 잔여수명 평가,' 대한기계학회논문집 A, 제21권, 1호, pp. 22-31
  3. 김효진, 정용근, 박종진, 2000, '발전소 고온부의 수명 평가를 위한 소형 시편용 크리프 시험기의 개발,' 대한기계학회논문집 A, 제24권, 10호, pp. 2597-2602
  4. 박태규, 윤기봉, 2000, '소형펀치 크리프 시험에 대한 수치해석 및 실험연구(I), 대한기계학회 2000년도 제2회 재료 및 파괴부문 학술대회 논문집, pp. 178-183
  5. Parker, J. D. and James, J. D., 1994, 'Disc-Bend Creep Deformation Behavior of $^1/_2Cr^1/_2Mo^1/_4V$ Low Alloy Steel,' Fifth International Conference on Creep and Fracture of Engineering Material and Structures, pp. 651-660
  6. Parker, J. D. and James, J. D., 1994, 'Creep Behavior of Miniature Disc Specimens of Low Alloy Steel,' ASME PVP, Vol. 279 Developments in a Progressing Technology pp. 167-172
  7. Ule, B., Sustar, T., Dobes, F. and Milicka, F., 1997, 'Small Punch Test Method Assessment for the Determination of the Residual Creep Life of Service Exposed Components: Outcomes from an Interlaboratory Exercise,' Intelligent Software System in Inspection and Life Management of Power and Process Plants, p. 263-276
  8. Tettamanti, S. and Crudeli, R., 1998, 'Small Punch Creep Test : A Promising Methodology for High Temperature Plant Components Life Evaluation,' BALTICA Ⅵ Plant Maintenance for Managing Life & Performance, vol. 2, pp. 501-509
  9. Parker, J. D. and Stratford, G. C., 1998, 'The Application of Miniature Disc Testing for the Assessment of Creep Damage in CrMoV Rotor Steel,' BALTICA Ⅵ Plant Maintenance for Managing Life & Performance, Vol. 2, pp. 477-488
  10. Ule, B., Sustar, T., Dobes, F. and Milicka, F., 1999, 'Small Punch Test Method Assessment for the Determination of the Residual Creep Life of Service Exposed Components,' Technology, Law and Insurance, Vol. 4, pp. 283-293 https://doi.org/10.1080/135993799349036
  11. Li, W. and Rodgers, B., 1999, 'A Finite Element and Experimental Study of Punch and Bulge Testing,' Key Engineering Materials, Vol. 167-168, pp. 55-63 https://doi.org/10.4028/www.scientific.net/KEM.167-168.55
  12. Brookfield, D. J., Li, W. and Rodgers, B., 1999, 'Material Properties from Small Specimens Using the Punch and Bulge Test,' Journal of Strain Analysis, Vol. 34, No. 6, pp. 423-435 https://doi.org/10.1243/0309324991513867
  13. Dobes, F., Milicka, K., 2000, 'Comparision of Creep Proerties of Power Plant Pipe Bends after Long Term Exposure,' 26th MPA-Seminar, pp. 24.1-24.10
  14. 권진오, 윤기봉, 이해무, 200, '0.5Cr-0.5Mo-0.25V 주조강의 크래프-피로 균열성장 거동 모델링,' 대한금속재료학회지, 제38권, 2호, pp. 285-291

Cited by

  1. A Direct Methodology for Small Punch Creep Test vol.56, pp.3, 2016, https://doi.org/10.1007/s11340-015-0108-z