초록
본 연구의 목적은 산부식된 법랑질에 수분이나 타액이 오염되어도 적절한 접착력을 얻을 수 있다고 소개된 교정용 친수성 프라이머를 이용한 교정용 브라켓 접착시 타액 오염 정도에 따른 전단결합강도와 접착 파절 양상을 기존의 소수성 프라이머와 비교함으로써 임상적 유용성을 평가하는 것이다. 사람의 소구치를 강철 원통에 교정용 레진으로 포매하여 만든 시편에 기존의 소수성인 Transbond XT primer와 친수성인 Transbond MIP primer각각에 대하여 광중합형 접착 레진으로 브라켓을 접착시, 인공 타액을 이용한 오염정도에 따른 전단결합강도를 만능시험기로 측정하고, 접착 파절 양상을 stereomicroscope로 관찰하여 다음과 같은 결과를 얻었다. 1. 건조 상태에서 Transbond XT primer와 Transbond MIP primer의 전단결합강도는 유의한 차이가 없었다. 2. 타액 오염시 그 정도에 상관없이 Transbond MIP primer는 Transbond XT primer에 비해 유의하게 높은 전단결합 강도를 나타냈다(p<0.001). 3. Transbond MIP primer는 한 겹의 타액 오염시 건조 상태와 전단결합강도의 유의한 차이가 없었으나, 두 겹의 타액 오염시에는 유의하게 낮은 결합강도를 나타냈다(p<0.01). 4. 접착 파절 형태는 타액 오염의 정도에 따라 평균 접착제 잔류 지수가 낮아지는 경향을 나타냈다. Transbond MIP primer는 타액 오염시에도 반 이상이 브라켓-레진 계면에서의 파절을 보였으나, Transbond XT primer는 타액 오염시 대부분의 경우 레진-법랑질 계면에서의 파절을 나타냈다. 이상의 실험 결과, 교정용 친수성인 Transbond MIP primer는 수분 조절이 어려운 임상 상황에서 적절한 결합강도를 얻을 수 있는 좋은 방법으로 생각된다.
The purpose of this study was to evaluate the clinical effectiveness of hydrophilic primer, which claim to retain adequate bond strength on moistened enamel resulting from moisture or saliva contamination, by comparing the shear bond strength and adhesive failure patterns of brackets bonded using hydrophilic primer and conventional hydrophobic primer. Brackets were bonded to human premolars embedded in metal cylinders utilizing light cured adhesive, primed with either a hydrophilic primer(Transbond fm primer) or a conventional hydrophobic primer(Transbond XT primer). Each sample was exposed to varying degrees of artificial saliva contamination during the priming process. The shear bond strength was measured using a universal testing machine, and the adhesive failure patterns after debonding were visually examined by strereomicroscope and assessed using the adhesive remnant index(ARI). The results were as follows 1. In dry conditions, no significant differences in shear bond strength between Transbond W and Transbond XT primers were found. 2. Transbond MIP primer exhibited a significantly higher shear bond strength than Transbond XT primer in saliva-contaminated conditions, regardless of the degree of contamination. 3. When contaminated with one coat of saliva, Transbond MIP primer did not exhibit significant differences in shear bond strength compared to the dry condition. When contaminated with two coats of saliva, Transbond MIP primer exhibited a singnificantly lower shear bond strength compared to the dry condition. 4. The adhesive remnant index of the adhesive failure pattern had a tendency to decrease, as the degree of saliva contamination increased. Bracket-adhesive interface failure was observed in more than half of the saliva contaminated samples utilizing Transbond MIP primer, whereas the bond failure sites of the Transbond XT primer samples occurred almost exclusively at the adhesive-enamel interface in saliva-contaminated conditions. The results of this study suggest that in cases where moisture control is difficult, Transbond MIP primer is an effective alternative to conventional hydrophobic primers.