J and CTOD Estimation for Homogeneous and Bi-Material Fracture Toughness Testing Specimens

  • Published : 2001.08.01

Abstract

This paper proposes J and CTOD estimation schemes applied to fracture toughness testing, covering typical homogeneous and bi-material specimens. Recommendations are based on the plastic limit analysis (either slip line field or finite element limit analyses), assuming the rigid plastic material behavior. The main outcome of the present study is that the J and CTOD estimation schemes (both codified and non-codified), recommended for homogeneous specimens, can be equally used for bi-material specimens with interface cracks. The effect of yield strength mismatch in bi-material specimens on the J-integral CTOD is discussed.

Keywords

References

  1. ASTM E1290, 'Standard Test Method for Fracture Toughness Testing of Ferritic Steel Weldments' (draft)
  2. ASTM Standards, Section 3, Vol. 3. 01 see British Standards, BS 5447, 'Methods of Test for Plane Strain Fracture Toughness of Metallic Materials'
  3. British Standards, BS 7448, 'Methods for Determination of Kic,Critical CTOD and Critical J Values of Welds in Metallic Materials' (draft)
  4. E1152-87 'Standard Test Method for Determining J-R Curves'
  5. E399-83 'Standard Test Method for Plane Strain Fracture Toughness of Metallic Materials'
  6. E561-86 'Standard Practice for R-Curve Determination'
  7. E813-87 'Jic, a Measure of Fracture Toughness'
  8. ISO/CD 12135, 'Metallic Materials-Unified Method of Test for the Determination of Quasistatic Fracture Toughness'
  9. ISO/CD 15653, 'Metallic Materials-Unified Method of Test for the Determination of Quasistatic Fracture Toughness of Welds' (draft)
  10. Joyce, J. A. and Link, R. E. 1994, Effects of Tensile Loading on Upper Shelf Fracture Toughness, NUREG/CR-6051
  11. Kim, Y.-J. and Lee, H., 1996, 'Interfacial Crack-Tip Constraints due to Elastic T-Stresses on Bimaterial Interfaces,' Proceedings of 96 APCFS,Kyung-Ju,Korea, pp. 511-516
  12. Kim, Y.-J. and Schwalbe K.-H., 2001a, 'On Sensitivity of J Estimation to Material's Stress Strain Curves in Fracture Toughness Testing UsIing Finite Element Method,' ASME Journal of Testing and Evaluation, Vol. 29, pp. 18-30
  13. Kim, Y.-J. and Schwalbe K.H., 2001b, 'Mismatch Effect on Plastic Yield Loads in Idealized Weldments II-Heat Affected Zone Cracks,' Engineering Fracture Mechanics, Vol. 68, pp. 183-199 https://doi.org/10.1016/S0013-7944(00)00094-1
  14. Kim, Y.-J., 1994, 'Fully Plastic Analyses of plane Strain Single Edge Cracked Bi-Material Specimens under Combined Bending and Tension,' GKSS Internal Report, GKSS/WAW/94/12, GKSS Research Center, Geesthacht, Germany
  15. Kirk, M. T. and Dodds, R. H., 1993, 'J and CTOD Estimation Equations for Shallow Cracks in Single Edge Notch Bend Specimen,' Journal of Testing and Evaluation, Vol. 21, No. 4, pp. 228-238
  16. Kirk, M. T. and Wang, Y.-Y., 1995, 'Wide Range CTOD Estimation Formulae for SE(B) Specimens,' ASTM STP 1256:Fracture Mechanics, pp. 126-141
  17. Lee, H. and Kim, Y.-J., 1998, 'Effect of Strength Mismatch on Fully Plastic Fields in Bimaterial Joints under Combined Loading,' KSME International Journal, Vol. 12, No. 4, pp. 553-564
  18. Lee, H. and Parks, D. M., 1993, 'Fully Plastic Analyses of Plane Strain Single-Edge-Cracked Specimens Subject to Combined Tension and Bending,' International Journal of Fracture, Vol. 63, pp. 329-349 https://doi.org/10.1007/BF00013042
  19. Lee, H., Ham, J. and Kim, Y.-J., 1999, 'MBL Based Investigations of Interfacial Crack-Tip Constraints and J-integrals in Platically Hardening Bimaterials,' Transactions of KSME(A), Vol. 23,No. 9, pp. 1525-1535
  20. Rice, J. R., Paris, P. C. and Merkle, J. Gf., 1973, 'Some Further Results of J-Integral Analysis and Estimates', ASTM STP 536, American Society of Testing and Materials, Philadelphia, pp. 231-245
  21. Sharobeam, M. H. and Landes, J. D., 1991, 'The Separation Criterion and Methodology in Ductile Fracture Mechanics,' International Journal of Fracture, Vol. 47, No. 2, pp. 81-104 https://doi.org/10.1007/BF00032571
  22. Sharobeam, M. H. and Landes, J. D., 1993, 'The Load Separation and ηpl Development in Precracked Specimen Test Records,' International Journal of Fracture, Vol. 59, pp. 213-226 https://doi.org/10.1007/BF02555184
  23. Wang, Y.-Y, and Gordon, J. R., 1992, 'The Limits of Applicability of J and CTOD Estimation Procedures for Shallow Cracked SENB Specimens,' in Shallow Crack Fracture Mechanics, Toughness Tests and Applications, Cambrige, UK
  24. Wu, S. X., Cotterell, B. and Mai, Y. W., 1988, 'Slip Line Field Solutions for Three-Point Notch Bend Specimens,' International Journal of Fracture, Vol. 37, pp. 13-29 https://doi.org/10.1007/BF00017820
  25. Wu, S. X., Mai, Y. W., and Cotterell, B., 1990, 'Plastic ${\eta}$-factor(ηp) of Fracture Specimens with Deep and Shallow Cracks,' International Journal of Fracture, Vol. 45, pp. 1-18 https://doi.org/10.1007/BF00012606