Journal of Mechanical Science and Technology

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지

Phenomenological Combustion Modeling of a Direct Injection Diesel Engine with In-Cylinder Flow Effects

  • Im, Yong-H. (Department of Mechanical Engineering, Pohang University of Science & Technology) ;
  • Huh, Kang-Y. (Department of Mechanical Engineering, Pohang University of Science & Technology)
  • Published : 2000.05.01
Download PDF
⟨ Previous Next ⟩

Abstract

A cycle simulation program is developed and its predictions are compared with the test bed measurements of a direct injection (DI) diesel engine. It is based on the mass and energy conservation equations with phenomenological models for diesel combustion. Two modeling approaches for combustion have been tested; a multi-zone model by Hiroyasu et al (1976) and the other one coupled with an in-cylinder flow model. The results of the two combustion models are compared with the measured imep, pressure trace and NOx and soot emissions over a range of the engine loads and speeds. A parametric study is performed for the fuel injection timing and pressure, the swirl ratio, and the squish area. The calculation results agree with the measured data, and with intuitive understanding of the general operating characteristics of a DI diesel engine.

Keywords

References

  1. Austen, A. E. and Lyn, W. T., 1961, 'Some Step toward Calculating Diesel Engine Behavior,' SAE paper 409A
  2. Borgnakke, C., Davis, G. C. and Tabaczynski, R. J., 1981, 'Prediction of In-Cylinder Swirl Velocity and Turbulence Intensity for an Open Chamber Cup in Piston Engine,' SAE paper 810224
  3. Chae, J. O., Jianwen, Li, Park, J. K. and Jeong, Y. S. et al, 1996, 'A Comparison of Predicted and Measured Results for a Single-Cylinder DI Diesel Engine at Different Intake Pressure & Composition,' Proceedings of the 3rd KSME-JSME Thermal Engineering Conference (I), pp. 323-326
  4. Chiu, W. S., Shaded, S. M. and Lyn, W. T., 1976, 'A Transient Spray Mixing Model for Diesel Combustion,' SAE paper 760128
  5. Heywood, J. B., 1988, Internal Combustion Engine Fundamentals, (Singapore: Mcgraw-Hill)
  6. Hiroyasu, H. and Kadota, T., 1976, 'Models for Combustion and Formation of Nitric Oxide and Soot in Direct Injection Diesel Engine,' SAE paper 760129
  7. Hiroyasu, H. and Kadota, T., 1983, 'Development and Use of a Spray Combustion Modeling to Predict Diesel Engine Efficiency and Pollutant Emissions,' Bulletin of the JSME, 26
  8. Kono, S., Nagao, A. and Motooka, H., 1985, 'Prediction of In-Cylinder Flow and Spray Formation Effects on Combustion in Direct Injection Diesel Engine,' SAE paper 850108
  9. Kriger, R. B. and Borman, G. L., 1966, 'The Computation of Apparent Heat Release for Internal Combustion Engines,' ASME Paper 66-WA/OGP-4
  10. Matsuoka, S. and Yoshizaki, T., 1989, 'Model Verification of Burned Gas Re- Entrainment Phenomenon and the Soot Formation Mechanism in Diesel Combustion (Free Spray Flame in Rapid Compression Machine),' SAE paper 89040
  11. Nishida, K. N. and Hiroyasu, H., 1989, 'Simplified Three-Dimensional Modeling of Mixture Formation and Combustion in a D. I. Diesel Engine,' SAE paper 890296
  12. Tabaczynski, R. J. and Ferguson, C. R., 1977, 'A Turbulent Entrainment Model for Spark-Ignition Engine Combustion,' SAE paper 770647
  13. Woschni, G., 1967, 'Universally Applicable Equation for the Instantaneous Heat Transfer Coefficient in the Internal Combustion Engine,' SAE paper 670931
  14. Xiaobin, L. and Wallace, J. S., 1995, 'A Phenomenological Model for Soot Formation and Oxidation in Direct Injection Diesel Engines,' SAE paper 952428
  15. Turns, S. R., 1993, An Introduction to Combustion, (Singapore: Mcgraw-Hill), pp. 305-315
  16. Sato, G. T. and Tanabe, H. T., 1982, 'Study on Diesel Spray and its Combustion,' Proc. XIXth Int. FISTA, No. 82027
  17. Lyn, W. T., 1962, 'Study of the Burning Rate and Nature of Combustion in Diesel Engines,' 9th Symposium (int ernational) on Combustion, pp. 1069-1082
  18. Payri, F. and Benajes, J., 1988, 'A Phenomenological Combustion Model for Direct Injection, Compression-Ignition Engines,' APPL Math. Modelling, Vol. 12 https://doi.org/10.1016/0307-904X(88)90037-6
  19. Rosli, A. B. and Lee, C. S., 1997, 'The Effect of Combustion Parameters on the Nitric Oxide Emission in Direct Injection Type Diesel Engine,' KSME Int. J., Vol. 11, No.6, pp. 672-680