Structural Engineering and Mechanics

  • 제10권2호
  • /
  • Pages.125-138
  • /
  • 2000
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Non-tubular bonded joint under torsion: Theory and numerical validation

  • Pugno, Nicola (Department of Structural Engineering, Politecnico di Torino) ;
  • Surace, Giuseppe (Department of Aeronautical and Space Engineering, Politecnico di Torino)
  • 발행 : 2000.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

The paper analyzes the problem of torsion in an adhesive non-tubular bonded single-lap joint. The joint considered consists of two thin rectangular section beams bonded together along a side surface. Assuming the materials involved to be governed by linear elastic laws, equilibrium and compatibility equations were used to arrive at an integro-differential relation whose solution makes it possible to determine torsional moment section by section in the bonded joint between the two beams. This is then used to determine the predominant stress and strain field at the beam-adhesive interface (stress field along the direction perpendicular to the interface plane, equivalent to the applied torsional moment and the corresponding strain field) and the joint's elastic strain (absolute and relative rotations of the bonded beam cross sections). All the relations presented were obtained in closed form. Results obtained theoretically are compared with those given by a three dimensional finite element numerical model. Theoretical and numerical analysis agree satisfactorily.

키워드

참고문헌

  1. Adams, R.D. and Peppiatt, N.A. (1977), "Stress analysis of adhesive bonded tubular lap joints", J. Adhesion, 9, 1-18. https://doi.org/10.1080/00218467708075095
  2. Alwar, R.S. and Nagaraja, Y.R. (1976), "Viscoelastic analysis of an adhesive tubular joint", J. Adhesion, 8, 79- 92. https://doi.org/10.1080/00218467608075072
  3. Bryant, R.W and Dukes, W.A. (1965), "The measurement of the shear strenght of adhesive joints in torsion", Brit. J. Appl. Phys., 16, 101-108. https://doi.org/10.1088/0508-3443/16/1/316
  4. Chen, D. and Cheng, S. (1992a), "Torsional stress in tubular lap joints", Int. J. Solids and Structures, 29, 845- 853. https://doi.org/10.1016/0020-7683(92)90020-T
  5. Chen, D. and Cheng, S. (1992b), "Torsional stresses in tubular lap joints with tapered adherends". J. Engineering Mechanics. ASCE. 118, 1962-1973. https://doi.org/10.1061/(ASCE)0733-9399(1992)118:9(1962)
  6. Choi, J.H. and Lee, D.G. (1994), "The torque transmission capabilities of the adhesively-bonded tubular single lap joint and the double lap joint", J. Adhesion. 44, 197-212. https://doi.org/10.1080/00218469408027077
  7. Chon, C.T. (1982), "Analysis of tubular lap joint in torsion", J. Composite Materials. 16, 268-284. https://doi.org/10.1177/002199838201600402
  8. Gent, A.N. and Yeoh, 0.H. (1982), "Failure loads for model adhesive joints subjected to tension, compression or torsion", J. Materials Science. 17, 1713-1722. https://doi.org/10.1007/BF00540799
  9. Graves, S.R. and Adams, D.F. (1981), "Analysis of a bonded joint in a composite tube subjected to torsion", J. Composite Materials. 15, 211-224. https://doi.org/10.1177/002199838101500302
  10. Hipol, P.J. (1984), "Analysis and optimization of a tubular lap joint subjected to torsion", J. Composite Materials. 18, 298-311. https://doi.org/10.1177/002199838401800401
  11. Jeong, K.S., Lee, D.G., Kwak, Y.K. (1995), "Application of adhesive joining technology for manufacturing of the composite flexspline for a harmonic drive", J. Adhesion. 48, 195. https://doi.org/10.1080/00218469508028162
  12. Kim, K.S., Kim, W.T., Lee, D.G., Jun, E.J. (1992), "Optimal tubular adhesive-bonded lap joint of the carbon-fiber epoxy composite shaft", Composite Structures. 21, 163-176. https://doi.org/10.1016/0263-8223(92)90016-6
  13. Kim, W.T. and Lee, D.G. (1995), "Torque transmission capabilities of adhesively bonded tubular lap joints for composite drive shafts", Composite Structures. 30, 229-240. https://doi.org/10.1016/0263-8223(95)80017-4
  14. Lee, D.G., Kim, K.S., lm, Y.T. (1991), "An experimental-study of fatigue-strength for adhesively bonded tubular single lap joints", J. Adhesion. 35, 39-53. https://doi.org/10.1080/00218469108030434
  15. Lee, S.J. and Lee, D.G. (1992), "Development of a failure model for the adhesively bonded tubular single lap joint", J. Adhesion. 40, 1-14. https://doi.org/10.1080/00218469208030467
  16. Lee, S.J. and Lee, D.G. (1995), "An iterative solution for the torque transmission capability of adhesively-bonded tubular single lap joints with nonlinear shear properties", J. Adhesion, 53, 217-227. https://doi.org/10.1080/00218469508009940
  17. Lee, S.W, Lee, D.G. and Jeong, K.S. (1997), "Static and dynamic torque characteristics of composite cocured single lap joint", J. Composite Materials. 31, 2188-2201. https://doi.org/10.1177/002199839703102104
  18. Lubkin, J.L and Reissner, E. (1956), "Stress distribution and design data for adhesive lap joints between circular tubes", Trans. ASME. 78, 1213-1221.
  19. Matsui, K. (1991), "Size efffect on nominal ultimate shear stresses of adhesive-bonded circular or rectangular joints under torsion", Int. J. Adhesion and Adhesives. 11, 59-64. https://doi.org/10.1016/0143-7496(91)90027-F
  20. Matsui, K., Ueda, Y, Aihara, Y. and Miyazaki, H. (1986), "Size-effect on ultimate shear stress of adhesive-bonded tubular lap or tubular butt or circular scarf butt joint uncer twisting load", J. Adhesion Soc. Japan, 22, 479-483.
  21. Matsui, K., Ueda, Y., Morikawa, Y and Yoshino, T. (1987), "Size-effect on ultimate torsional stress of adhesive-bonded joint with a rectangular cross section", J. Adhesion Soc. Japan. 23, 96-102.
  22. Medri, G. (1977), "Il calcolo delle tensioni nell'adesivo in giunti tra tubi sollecitati da momento torcente", Ingegneria Meccanica. 7/8, 247-251.
  23. Medri, G. (1988), "Viscoelastic analysis of adhesive bonded lap joints between tubes under torsion", J. of Vibration Acoustics Stress and Reliability in Design-Transactions. ASME. 110, 384-388. https://doi.org/10.1115/1.3269530
  24. Moloney, A.C., Kausch, H.H. and Stieger, HR. (1984), "The use of the double torsion test geometry to study the fracture of adhesive joints", J. Materials Science letters. 3, 776-778. https://doi.org/10.1007/BF00727970
  25. Nayebhashemi, H., Rossettos, J.N. and Melo, AP. (1997), "Multiaxial fatigue life evaluation of tubular adhesively bonded joints", Int. J. Adhesion and Adhesives. 17, 55-63. https://doi.org/10.1016/S0143-7496(96)00023-1
  26. Prakash, V., Chen, C.M., Engelhard, A. and Powell, G. (1995), "Torsional fatigue test for adhesive-bonded butt joints", J. Testing and Evaluation. 23, 228-230. https://doi.org/10.1520/JTE10415J
  27. Pugno, N. (1998), "Non tubular bonded joints under torsion", Ph.D. Thesis, Dept. of Structural Engineering, Politecnico di Torino, Torino, Italy.
  28. Pugno, N. (1999), "Optimizing a non-tubular adhesive bonded joint for uniform torsional strength", Int. J. of Materials and Product Technology, 14, 476-487. https://doi.org/10.1504/IJMPT.1999.036285
  29. Pugno, N. and Surace, G. (1998a), "Ottimizzazione di un giunto incollato tubular-lap progettato ad uniforme resistenza a torsione". Proceedings of XXVll AIAS, 1043-1052, Perugia, Italy.
  30. Pugno, N. and Surace, G. (1998b), "Theorectical tensional analysis of a single lap bonded joint subjected to torsion". Proceedings of VII NMCM. 189-195, Hihg Tatras, Slovak Republic.
  31. Pugno, N. and Surace, G. (1998c), "Analisi teorica tensionale di un giunto incollato double-lap soggetto a torsione". Proceedings of XXVll AlAS. 1053-1062, Perugia, Italy.
  32. Rao, M.D. and Zhou, H. (1994), "Vibration and damping of a bonded tubular lap joint". J. Sound and Vibration. 178, 577-590. https://doi.org/10.1006/jsvi.1994.1506
  33. Reedy, E.D. and Guess, T.R. (1993), "Composite-to-metal tubular lap joints strength and fatigue resistance", Int. J. Fracture. 63, 351-367. https://doi.org/10.1007/BF00013043
  34. Vonesebeck, G., Kising, M. and Neuhof, U., (1996), "Investigation on ceramic-metal joints for shaft-hub connections in gas-turbines", J. of Engineering for Gas Turbines and Power-Transactions of the ASME, 118, 626-631. https://doi.org/10.1115/1.2816694
  35. Zhou, H.M. and Rao, M.D. (1993), "Viscoelastic analysis of bonded tubular joints under torsion", Int. J. Solids and Structures, 30, 2199-2211. https://doi.org/10.1016/0020-7683(93)90083-J

피인용 문헌

  1. Strength, stability and size effects in the brittle behaviour of bonded joints under torsion: theory and experimental assessment vol.25, pp.1, 2002, https://doi.org/10.1046/j.1460-2695.2002.00461.x
  2. Tubular bonded joint under torsion: Theoretical analysis and optimization for uniform torsional strength vol.36, pp.1, 2001, https://doi.org/10.1243/0309324011512577
  3. Tubular Adhesive Joints Under Axial Load vol.70, pp.6, 2003, https://doi.org/10.1115/1.1604835
  4. Thermal loading in multi-layered and/or functionally graded materials: Residual stress field, delamination, fatigue and related size effects vol.43, pp.3-4, 2006, https://doi.org/10.1016/j.ijsolstr.2005.05.009
  5. A generalization of the Coulomb’s friction law: from graphene to macroscale vol.48, pp.8, 2013, https://doi.org/10.1007/s11012-013-9789-5
  6. Evaluation of torsional natural frequencies for non-tubular bonded joints vol.13, pp.1, 2002, https://doi.org/10.12989/sem.2002.13.1.091