DOI QR코드

DOI QR Code

Improved numerical approach for the bond-slip behavior under cyclic loads

  • Kwak, H.G. (Department of Civil Engineering, Korea Advanced Institute of Science and Technology)
  • Published : 1997.09.25

Abstract

Bond-slip behavior between reinforcement and concrete under push-pull cyclic loadings is numerically investigated based on a reinforcement model proposed in this paper. The equivalent reinforcing steel model considering the bond-slip effect without taking double nodes is derived through the equilibrium at each node of steel and the compatibility condition between steel and concrete. Besides a specific transformation algorithm is composed to transfer the forces and displacements from the nodes of the steel element to the nodes of the concrete element. This model first results in an effective use in the case of complex steel arrangements where the steel elements cross the sides of the concrete elements and second turns the impossibility into a possibility in consideration of the bond-slip effect in three dimensional finite element analysis. Finally, the correlation studies between numerical and experimental results under the continuously repeated large deformation stages demonstrate the validity of developed reinforcing steel model and adopted algorithms.

Keywords

References

  1. ASCE Task Committee on Finite Element Analysis of Reinforced Concrete Structures (1982), State-of the-Art Report on Finite Element Analysis of Reinforced Concrete, ASCE Special Publications.
  2. Ciampi, V., Eligehausen, R., Popov, E.P. and Bertero, V.V. (1982), "Analytical model for concrete anchorages of reinforcing bars under generalized excitations", Report No. UCB/EERC-82/23, Earthquake Engineering Research Center;University of California, Berkeley.
  3. Choi, C.K. and Kwak, H.G. (1990), "The effect of finite element mesh sizes in nonlinear finite element analysis of R/C structures", Computers and Structures, 36(4), 175-186.
  4. Crisfield, M.A. (1982), "Accelerated solution techniques and concrete cracking", Computer Methods in Applied Mechanics and Engineering, 33, 585-607. https://doi.org/10.1016/0045-7825(82)90124-4
  5. de Groot, A.K., Kusters, G.M.A. and Monnier, T. (1981), "Numerical modeling of bond-slip behavior", Heron, Concrete Mechanics, 26(1B).
  6. Eligehausen, R., Popov, E.P. and Bertero, V.V. (1983), "Local bond stress-slip relationships of deformed bars under generalized excitations", Report No. UCB/EERC 83-23, Earthquake Engineering Research Center, University of California, Berkeley.
  7. Filippou, F.C. (1986), "A simple model for reinforcing bar anchorages under cyclic excitations", Journal of Structural Engineering, ASCE, 112(7), 1639-1659. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:7(1639)
  8. Filippou, F.C., Popov, E.P. and Bertero, V.V. (1983), "Effects of bond deterioration on hysteretic behavior of reinforced concrete joints", Report No. UCB/EERC-83/19, Earthquake Engineering Research Center;University of California, Berkeley.
  9. Hayashi, S. and Kokusho, S. (1985), "Bond behavior in the neighborhood of the crack", Proceedings of the U.S.-Japan Joint Seminar on Finite Element Analysis of Reinforced Concrete, 364-373, Tokyo, Japan.
  10. Keuser, M. and Mehlhorn, G. (1987), "Finite element models for bond problems", Journal of Structural Engineering, ASCE, 113(10), 2160-2173. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:10(2160)
  11. Kwak, H.G. and Filippou, F.C. (1990), "Finite element analysis of reinforced concrete structures under monotonic loads", Report No. UCB/SEMM-90/14, University of California, Berkeley.
  12. Menegotto, M. and Pinto, P. (1973), "Method of analysis for cyclically loaded reinforced concrete plane frames including changes in geometry and nonelastic behavior of elements under combined normal force and bending", IABSE Symposium on Resistance and Ultimate Deformabilily of Structures Acted on by Well-Defined Repeated Loads, Final Report, Lisbon.
  13. Ngo, D. and Scordelis, A.C. (1967), "Finite element analysis of reinforced concrete beams", Journal of ACI, 64(3), 152-163.
  14. Viwathanatepa, S., Popov, E.P. and Bertero, V.V. (1979), "Seismic behavior of reinforced concrete interior beam-column subassemblages", Report No. UCB/EERC-79/14, Earthquake Engineering Research Center, University of California, Berkeley.
  15. Yankelevsky, D.Z. (1985), "New finite element for bond-slip analysis", Journal of Structural Engineering, ASCE, 111(7), 533-1542. https://doi.org/10.1061/(ASCE)0733-9445(1985)111:7(1533)
  16. Zulfiqar, N. and Filippou, F.C. (1990), "Models of critical regions in reinforced concrete frames under seismic excitations", Report No. UCB/EERC-90/06, Earthquake Engineering Research Center, University of California, Berkeley.

Cited by

  1. Cracking analysis of RC members using polynomial strain distribution function vol.24, pp.4, 2002, https://doi.org/10.1016/S0141-0296(01)00112-2
  2. Improved FE model to simulate interfacial bond-slip behavior in composite beams under cyclic loadings vol.125, 2013, https://doi.org/10.1016/j.compstruc.2013.04.020
  3. Numerical modelling of the cyclic behaviour of RC elements built with plain reinforcing bars vol.33, pp.2, 2011, https://doi.org/10.1016/j.engstruct.2010.11.005
  4. Monotonic moment–curvature relation of an RC beam vol.54, pp.6, 2002, https://doi.org/10.1680/macr.2002.54.6.423
  5. Overview on the bonding of reinforced concrete under pristine, corrosive and freeze-thaw conditions pp.1568-5616, 2019, https://doi.org/10.1080/01694243.2018.1559439
  6. Numerical Modeling of RC Columns and a Modified Steel Model Proposal for Elements With Plain Bars vol.6, pp.None, 1997, https://doi.org/10.3389/fbuil.2020.586690