Effects of Wilting and Additives on the Fermentation Chrateristics , Quality and Aerobic Stability of Rye Silage

예건 및 첨가제가 호밀사일리지의 발효특성과 사료가치 및 호기적 안정성에 미치는 영향

This experiment was conducted to evaluate effects of wilting and additives on fermetation characteristics, quality and aerobic stability of silage of rye(Seca1e cereale L.) harvested at the early heading stage. Harvested rye was wilted or mixed with beet pulp and then treated with formic acid or lactic acid bacteria(LAB) inoculant. Treatments were consisted of direct cut(DC), wilted(WT), beet pulp added(BP), direct cut and formate applied(DF), wilted and formate applied(WF), beet pulp and formate applied(BF), direct cut and LAB inoculated(DL), beet pulp added and LAB inoculated(BL), and wilted and LAB inoculated(WL) silages. Afler 70 days of ensiling period, the silages were opened and exposed to air for 7 days, and the silages of opening day(0 day) were compared with the silages exposed to air for 7 days(7 day). 1. LAB inoculated rye silages(DL, WL, BL) lowered pH values effectively eom the third day of ensiling and showed most stable pattern of pH changes during the initial fermentation process. Direct cut and formate applied(DF), beet pulp and formate applied(BF) and beet pulp added(BP) silages were also effective in lowering pH from the seventh day thai direct cut treatment(DC). 2. pH was low below 3.7 in all treatments of 0 day. After 7-day period of aerobic exposure, DL and WL showed considerable increases in pH from 3.5 and 3.4 to 8.3 and 6.4, respectively. 3. Direct cut rye silages(DF, DC, DL) and beet pulp and formate treatment(BF) produced effluent of 121.2, 85.9, 80.3 and 34.2 mlkg, respectively and these were greater than others(P<0.01). Beet pulp retained 1.61 I/kg of effluent at the application rate of 50 kg/t in comparing BP with DC, and formate application increased the amount of effluent in comparing DF and BF with DC and BP, respectively(P<0.01). 4. Beet pulp and LAB treatment(B1) was highest in content of lactate as 3.1% and formate treated silages(DF, WF, BF) showed lower content of lactate and total acid than others. LAB inoculated(D1, WL, BL) and wilted (WT) silages were graded to be good quality as a second group by the Flieg's score. Formate applied silages (DF, WF, BF) were graded as a foum group lower than DC by one. 5. Residual content of WSC of rye silage was higher in BP, BF, DL and BL than direct cut treatment(M3) (P< 0.01). Formate application had a tendency to increase the content of residual content of WSC. 6. For the ratio of NH3-N to Total N, wilted and LAB inoculated(W1) and direct cut and LAB inoculated(D1) silages were lowest on 0 day as 8.9 and 9.3% respectively. But after 7-day period of aerobic exposure, WL and DL showed largest increase of the ratio of $NH_3-N$ to Total N from 0 day(P<0.01). 7. On 0 day wilted(WT), beet pulp and formate treatment(BF), and beet pulp and LAB treatment(B1) were lower than direct cut treatment(DC) for NDF and ADF concentrations consistently. Formate applied silages (DF, WF, BF) made little change in ADF and NDF concentrations during 7 day period of aerobic exposure. DL and WL showed a large increase in ADF and NDF concentrations under aerobic condition(P<0.01). 8. IVDMD values of wilted(WT), beet pulp added(BP), wilted and LAB inoculated(W1) and beet pulp added and LAB inoculated(B1) silages were higher than direct-cut treatmentPC) as 84.7, 84.7, 84.4 and 83.0%, respectively on 0 day. But during 7-day period of aerobic exposure, a great decreae in IVDMD of WL was showed(P<0.01). The experimental results indicate that wilted silage(WT) could be recommended as the most effective treatment for reducing efluent and increasing quality and feed value of rye silage without deteriorating aerobic stability more than direct cut treatment(DC). Additionally, under unfavorable weather condition beet pulp added and LAB inoculated treatment(T3L) might be the possible alternative for successful ensiling of forage rye.