• 제목, 요약, 키워드: End effect

검색결과 3,832건 처리시간 0.056초

단부효과에 의한 PMLSM의 디텐트력 저감을 위한 보조코어 최적설계 (The Auxiliary Core Optimal Design of PMLSM to Reduce Detent Force by End Effect)

  • 장기봉;안호진;김규탁
    • 전기학회논문지
    • /
    • v.59 no.3
    • /
    • pp.543-548
    • /
    • 2010
  • There are produced the detent force caused by slot-teeth structures, end-effect and parallel magnetization of permanent magnet in permanent magnet linear synchronous motor. In this paper, we proposed to establish the auxiliary core for reducing detent force which is generated the discontinuity of magnetic circuits by end effect. The optimal design of the auxiliary core used a finite element analysis and design of experiment. To demonstrate the validity of the paper, the experiment results are compared with analysis ones.

유도형 리니어 모터의 속도특성에 관한 연구 (A study on the speed characteristic of linear induction motor)

  • 정병호;최문한;조금배;백형래;서진연;김대곤
    • 전력전자학회:학술대회논문집
    • /
    • /
    • pp.151-154
    • /
    • 2004
  • To use the SLIM for servo system, the exact account of thrust about the initial speed is needed, but analyzing by equivalent circuit analyzing methode such as rotary induction motor, the error occurs because of the end effect. So, we applied the equivalent circuit considering the end effect of SLIM in this paper. The current control system is advanced the space vector pulse width modulation by using high arithmetic performance microprocessor such as DSP. In this paper, we use the dynamic characteristic analyzing methode that can calculate efficiently the end effect by using equivalent circuit methode in the operating SLIM system modeling and examine the output characteristics of SVPWM with PI controller.

  • PDF

Dynamic response of a hinged-free beam subjected to impact at an arbitrary location along its span with shear effect

  • Zhang, Y.;Yang, J.L.
    • Structural Engineering and Mechanics
    • /
    • v.26 no.5
    • /
    • pp.483-498
    • /
    • 2007
  • In case of considering the shear effect, the complete solutions are obtained for dynamic plastic response of a rigid, perfectly plastic hinged-free beam, of which one end is hinged and the other end free, subjected to a transverse strike by a travelling rigid mass at an arbitrary location along its span. Special attention is paid to new deformation mechanisms due to shear sliding on both sides of the rigid mass and the plastic energy dissipation. The dimensionless numerical results demonstrate that three parameters, i.e., mass ratio, impact position of mass, as well as the non-dimensional fully plastic shear force, have significant influence on the partitioning of dissipated energy and failure mode of the hingedfree beam. The shear effect can never be negligible when the mass ratio is comparatively small and the impact location of mass is close to the hinged end.

하향엔드밀링시 헬릭스각에 따른 절삭특성변화 (Cutting Characteristics in Down-End Milling with Different Helix Angles)

  • 이영문;장승일;서민교
    • 한국공작기계학회:학술대회논문집
    • /
    • /
    • pp.77-82
    • /
    • 2003
  • In end milling process, undeformed chip thickness and cutting force vary periodically with phase change of the tool. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting to this. In the current study, the varying undeformed chip thickness and the cutting forces in a down-end milling process have been replaced with the equivalent ones of oblique cutting. And, the down-end milling characteristics of SM45C has been compared with that of the up-end milling previously presented with different helix angles.

  • PDF

농형 유도전동기의 2차원 유한요소해석을 위한 엔드링 저항과 인덕턴스 계산 (Calculations of Resistance and Inductance of End Ring of the Squirrel Cage Induction Motor for 2-Dimensional Finite Element Analysis)

  • 정희준;신판석;우성현
    • 대한전기학회:학술대회논문집
    • /
    • /
    • pp.872-873
    • /
    • 2007
  • This paper proposes a calculating method of resistance and inductance of end ring of squirrel cage induction motor for 2D finite element analysis. The squirrel cage of induction motor consists of bars and end rings. The resistance and inductance of end ring have an effect on the result of the finite element calaculation. If the end ring were excluded from the analysis, the good result could not be obtained. Therefore, we first simulate an axisymmetric magnetodynamic analysis for the end ring, and then calculate the interbar resistance and the end ring inductance. The calculated values are put into the external circuit of 2D finite element model of the induction motor. The proposed method is verified by comparing the numerical results with the experimental ones.

  • PDF

쇄연장제가 폴리에스테르의 카르복실 말단기에 미치는 영향 (Effect of Chain Extenders on Carboxyl End Group of Polyester)

  • 김학용;은용수;조성호
    • 한국섬유공학회지
    • /
    • v.36 no.4
    • /
    • pp.267-273
    • /
    • 1999
  • Polyester was melt-blended with three kinds of chain extenders 2,2-bis-oxazoline (Bis1), 1,3-phenylene-bis-2-oxazoline (Bis2), and polycarbodiimide (PCBI), which can react with carboxyl end group of polyester. The effects of chain extender content and mixing time on the carboxyl end group content, intrinsic viscosity and cold crystallization temperature of polyester were investigated. When less than 1.0 wt% of Bis1 was added, the carboxyl end group concentration decreased below 10 meq/kg. For the Bis2 concentration of less than 1.0 wt%, the carboxyl end group concentration was between 18~49 meq/kg. When more than 1.5 wt% of PCBI was added, the carboxyl end group concentration decreased below 10 meq/kg. The intrinsic viscosity increased and carboxyl end group concentration decreased with increasing PCBI content.

  • PDF

엔드밀가공에서 커터회전방향에 따른 절삭력의 최적화 (Optimization of Cutting Force for End Milling with the Direction of Cutter Rotation)

  • 최만성
    • 반도체디스플레이기술학회지
    • /
    • v.16 no.2
    • /
    • pp.79-84
    • /
    • 2017
  • This paper outlines the Taguchi optimization methodology, which is applied to optimize cutting parameters in end milling when machining STS304 with TiAlN coated SKH59 tool under up and down end milling conditions. The end milling parameters evaluated are depth of cut, spindle speed and feed rate. An orthogonal array, signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are employed to analyze the effect of these end milling parameters. The Taguchi design is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer resources than a factorial design. An orthogonal array of $L_9(33)$ was used. The most important input parameter for cutting force, however, is the feed rate, and depending on the cutter rotation direction. Finally, confirmation tests verified that the Taguchi design was successful in optimizing end milling parameters for cutting force.

  • PDF

Aerodynamic Characteristics of Impulse Turbine with an End Plate for Wave Energy Conversion

  • HYUN BEOM SOO;MOON JAE SEUNG;HONG SEOK WON;KIM KI SUP
    • 한국해양공학회지
    • /
    • v.19 no.6
    • /
    • pp.1-7
    • /
    • 2005
  • This paper deals with the design and aerodynamic analysis of a special-type impulse turbine, with an end plate for wave energy conversion. Numerical analysis was performed using a CFD code, FLUENT. The main idea of the proposed end plate was to minimize the adverse effect of tip clearance of turbine blade, and was borrowed from ducted propeller, with so-called penetrating end plate for special purpose marine vehicles. Results show that efficiency increases up to $5\%$, depending on the flow coefficient; a higher flow coefficient yields increased efficiency. Decrease of input coefficient CAwith an end plate is the main reason for higher efficiency. Performance of end plate at various design parameters, as well as flow conditions, was investigated; the advantages and disadvantages of the presentimpulse turbine were also discussed.

관여, 광고위치, 광고형태에 따른 광고효과 연구 - 패션 인터넷 검색광고를 중심으로 - (A Study on Advertising Effect according to Involvement, Advertising Location and Advertising Forms - Focusing on the Fashion Internet Search Advertising -)

  • 제은숙
    • 복식문화연구
    • /
    • v.20 no.2
    • /
    • pp.251-262
    • /
    • 2012
  • This research aimed to examine an advertising location according to consumer involvement about internet search advertising and advertising effect according to advertising forms. This research carried out a questionnaire survey from May 25, 2011 for seven days with the target of men and women at the age of 20s-30s who tried search advertising in Seoul and capital area, and 519 copies were used for final analysis. For analysis of collected materials, the reliability test, factor analysis, $t$-test, regression analysis and ${\chi}^2$ test were executed by using statistical package SPSS 16.0. The results are as follows. First, it appeared that consumer's clothing involvement, advertising involvement, advertising location and advertising forms had an influence on site attitude and clicking intention. Consumers of high clothing involvement, high advertising involvement and upper end advertising appeared to have high site attitude and clicking intention. Second, all consumers of the low and high clothing involvement and upper end advertising appeared to prefer the upper end advertising. It appeared that consumers of low advertising involvement prefer lower end advertising, and consumers of high advertising involvement prefer the upper end advertising at an advertising location according to clothing involvement. Accordingly, it is important that the search advertising exposes advertising in the upper end, and that should use an advertising phrase capable of giving trust to consumers. As the text advertising had high site attitude and clicking intention in the advertising forms, consumers should pay attention to the advertising phrase.