DOI QR코드

DOI QR Code

Optimization of modular Truss-Z by minimum-mass design under equivalent stress constraint

  • Zawidzki, Machi (Institute of Fundamental Technological Research, Polish Academy of Sciences) ;
  • Jankowski, Lukasz (Institute of Fundamental Technological Research, Polish Academy of Sciences)
  • Received : 2017.05.20
  • Accepted : 2017.11.28
  • Published : 2018.06.25

Abstract

Truss-Z (TZ) is an Extremely Modular System (EMS). Such systems allow for creation of structurally sound free-form structures, are comprised of as few types of modules as possible, and are not constrained by a regular tessellation of space. Their objective is to create spatial structures in given environments connecting given terminals without self-intersections and obstacle-intersections. TZ is a skeletal modular system for creating free-form pedestrian ramps and ramp networks. The previous research on TZ focused on global discrete geometric optimization of the spatial configuration of modules. This paper reports on the first attempts at structural optimization of the module for a single-branch TZ. The internal topology and the sizing of module beams are subject to optimization. An important challenge is that the module is to be universal: it must be designed for the worst case scenario, as defined by the module position within a TZ branch and the geometric configuration of the branch itself. There are four variations of each module, and the number of unique TZ configurations grows exponentially with the branch length. The aim is to obtain minimum-mass modules with the von Mises equivalent stress constrained under certain design load. The resulting modules are further evaluated also in terms of the typical structural criterion of compliance.

Acknowledgement

Grant : Extremely Modular Systems for temporary and permanent deployable structures and habitats: development, modeling, evaluation & optimization

Supported by : National Science Centre

References

  1. Calafiore, G.C. and Dabene, F. (2008), "Optimization under uncertainty with applications to design of truss structures", Struct. Multidiscip.O., 35, 189-200. https://doi.org/10.1007/s00158-007-0145-z
  2. Christensen, P.W. and Klarbring, A. (2008), An Introduction to Structural Optimization, Springer Science & Business Media.
  3. Dunbar, G., Holland, C.A. and Maylor, E.A. (2004), "Older Pedestrians: A Critical Review of the Literature", Road Safety Research Report No. 37, Department for Transport, London, England.
  4. Jalkanen, J. and Koski, J. (2005), "Heuristic methods in space frame optimization", Proceedings of the 46th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, Austin, Texas, USA.
  5. Lavan, O. and Oded, A. (2014), "Simultaneous topology and sizing optimization of viscous dampers in seismic retrofitting of 3D irregular frame structures", Earthq. Eng. Struct. D., 43(9), 1325-1342. https://doi.org/10.1002/eqe.2399
  6. Martins, J.R.R.A. and Lambe, A.B. (2013), "Multidisciplinary design optimization: A survey of architectures", AIAA J., 51(9), 2049-2075. https://doi.org/10.2514/1.J051895
  7. Patnaik, S.N. and Hopkins, D.A. (1998), "Optimality of a fully stressed design", Comput. Method. Appl. M., 165(1-4), 215-221. https://doi.org/10.1016/S0045-7825(98)00041-3
  8. Pollack, M.E. (2005), "Intelligent technology for an aging population: The use of AI to assist elders with cognitive impairment", Artif. Intell. Mag., 26(2), 9-24.
  9. Poplawski, B., Mikulowski, G., Mroz, A. and Jankowski, L. (2018), "Decentralized semi-active damping of free structural vibrations by means of structural nodes with an on/off ability to transmit moments", Mech. Syst. Signal Pr., 100, 926-939. https://doi.org/10.1016/j.ymssp.2017.08.012
  10. Razani, A. (1965), "Behavior of fully stressed design of structures and its relationshipto minimum-weight design", AIAA J., 3(12), 2262-2268. https://doi.org/10.2514/3.3355
  11. Torstenfelt, B. and Klarbring, A. (2006), "Structural optimization of modular product families with application to car space frame structures", Structural and Multidisciplinary Optimization, 32(2), 133-140. https://doi.org/10.1007/s00158-005-0568-3
  12. Tugilimana, A., Thrall, A.P. and Coelho, R.F. (2017), "Conceptual design of modular bridges including layout optimization and component reusability", J. Bridge Eng., 22(11), 04017094. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001138
  13. Zawidzki, M. and Tateyama, K. (2011), "Application of evolution strategy for minimization of the number of modules in a truss branch created with the Truss-Z system", Proceedings of the 2nd International Conference on Soft Computing Technology in Civil, Structural and Environmental Engineering, Civil-Comp Press, Stirlingshire, UK, Paper 9.
  14. Zawidzki, M. (2011), Tiling of a Path with Trapezoids in a Constrained Environment with Backtracking Algorithm, Wolfram Demonstrations Project, http://demonstrations.wolfram.com/TilingOfAPathWithTrapezoidsInAConstrainedEnvironmentWithBack
  15. Zawidzki, M. and Nishinari, K. (2012), "Modular Truss-Z system for self-supporting skeletal free-form pedestrian networks", Adv. Eng. Softw., 47(1), 147-159. https://doi.org/10.1016/j.advengsoft.2011.12.012
  16. Zawidzki, M. and Nishinari, K. (2013), "Application of evolutionary algorithms for optimum layout of Truss-Z linkage in an environment with obstacles", Adv. Eng. Softw., 65, 43-59. https://doi.org/10.1016/j.advengsoft.2013.04.022
  17. Zawidzki, M. (2013), "Creating organic 3-dimensional structures for pedestrian traffic with reconfigurable modular Truss-Z system", Int. J. Des. Nature Ecodynam., 8(1), 61-87. https://doi.org/10.2495/DNE-V8-N1-61-87
  18. Zawidzki, M. (2015), "Retrofitting of pedestrian overpass by Truss-Z modular systems using graph-theory approach", Adv. Eng. Softw., 81, 41-49. https://doi.org/10.1016/j.advengsoft.2014.11.004