이종 상대재 경도에 따른 철강재료의 미끄럼 마모 특성 해석

• Lee, Han-Young (Keimyung University, Dept. of Advanced Materials Engineering)
• 이한영 (계명대학교 신소재공학과)
• Accepted : 2016.11.05
• Published : 2016.12.31

Abstract

This study examines the wear behavior of mild steel pins mated against alloyed tool steel discs in a pin-on-disc type sliding test machine and provides specific clarification regarding the effects of disc hardness on the wear behavior of a mating mild steel pin. The analysis confirms these effects through the observation of differences in the wear rates of the mild steel pins at low sliding speed ranges. These differences occur even though the hardness of the mating disc does not affect the wear characteristic curve patterns for the sliding speeds, regardless of the wear regime. In the running-in wear regime, increasing the hardness of the mating disc results in a decrease in the wear rates of the mild steel pins at low sliding speed ranges. However, in the steady-state wear region, the wear rate of a pin mated against the 42DISC is greater than the wear rate of a pin mated against the 30DISC, which has a lower hardness value. This means that the tribochemical reactivity of the mating disc, which is based on hardness value, influences the wear behavior of mild steel at low sliding speed ranges. In particular, oxides with higher oxygen contents, such as $Fe_2O_3$ oxides, form predominantly on the worn surface of the 42DISC. On the contrary, the wear behavior of mild steel pins at high sliding speed ranges is nearly unaffected by the hardness of the mating disc.

References

1. Sasada, T., "Wear testing method and wear properties of materials", Pro. 5th Wear Symposium of J. JSLE, pp.21-30, 1970.
2. Endo, Y., "Surface science", Chap. 4, pp. 64-73, Youkendo book co., Tokyo, Japan, 1985.
3. Egawa, K., "Effects of hardness of hardened steels on frictional wear (1st report)", J. JSLE, Vol. 19, No. 12, pp. 897-904, 1974.
4. Egawa, K., "Effects of hardness of hardened steels on frictional wear (2nd report)", J. JSLE, Vol. 19, No. 12, pp. 905-911, 1974.
5. Egawa, K., "Effects of hardness of hardened steels on frictional wear (3rd report)", J. JSLE, Vol. 26, No. 8, pp. 576-581, 1981.
6. Egawa, K., "Effects of hardness of hardened steels on frictional wear (4th report)", J. JSLE, Vol. 26, No. 11, pp. 771-778, 1981.
7. Egawa, K., "Characteristics of frictional wear of mild steel", J. JSLE, Vol. 26, No. 6, pp. 424-428, 1981.
8. Lee, H.-Y., "Effects of hardness on sliding wear behavior of tempered bearing steel", J. of KSTLE, Vol. 29, No. 6, pp. 360-365, 2013.
9. Sato K. et al., "Wear of Metals and its Counterplan", Chap. 1, pp. 9-18, Youkendo book co. Tokyo, Japan, 1965.
10. Lee, H.-Y., "Analysis of sliding wear mode on annealed steel by X-ray diffraction technique", Wear, Vol. 256, pp. 657-663, 2003.
11. Lee, H.-Y., Cho, Y.-J., Kim, T.-J., Park, W.-K., "Analysis of sliding wear properties for Aluminum ally according to the hardness values of the mating tool steel", J. JSTLE, Vol. 26, No. 2, pp.105-110, 2010.
12. Welsh, N. C., "The Dry Wear of Steel I. The general pattern of behavior", Phi. Trans. Royal Soc. London, series A, Vol. 257, No. 1077, pp. 31-50, 1965. https://doi.org/10.1098/rsta.1965.0001
13. Welsh, N. C., "The Dry Wear of Steel II. Interpretation and special features", Phi. Trans. Royal Soc. London, series A, Vol. 257, No. 1077, pp. 51-70, 1965. https://doi.org/10.1098/rsta.1965.0002
14. Karl-Heinz zum Gahr, "Microstructure and Wear of Materials", Chap. 6, pp. 378-380, Elsevier, New York, USA, 1987. (ISBN 0-444-42754-6)
15. Smith, W. F., Hashemi, J. "Foundations of Materials Science and Engineering", 4th Edition, Chap. 13, pp.640 (in book distributed by Scitech Media), McGraw-Hill Korea Inc., 2005. (ISBN 978-89-5550-552-80)