Temperature control of the Rework-system using fuzzy PID controller

퍼지 PID 제어기에 의한 리워크 시스템의 온도제어

  • Oh, Kabsuk (Department of Automotive Engineering, TongMyong University) ;
  • Kang, Geuntaek (Department of Electronics Engineering, Pukyong National University)
  • Received : 2014.09.03
  • Accepted : 2014.10.10
  • Published : 2014.10.31


Rework systems are the equipment used to install or remove semiconductor chips with BGA or SMD forms in printed circuit boards. The rework systems have hot air outlets. At the outlets, precise temperature control is needed to avoid heat shock. The aim of this paper was to suggest a new controller for temperature control at the hot air outlets. The suggested controller was a fuzzy PID controller. The fuzzy PID controllers were composed of TSK fuzzy rules and had outstanding ability for nonlinear systems control. This paper reports the design algorithm of fuzzy PID controllers, and the design process of the fuzzy PID controller for the temperature control of the outlets. Temperature control experiments were performed to verify the ability of the suggested controller. As a result, the RMS of the proposed method is 9.44 and the general method is 15.88. The experiments showed that the temperatures at the outlet using the suggested fuzzy PID controller followed the desired ones better than the commonly used PID controller.


TSK Fuzzy Model;Fuzzy PID Controller;Nonlinear Systems Control;Hot Air Temperature Control;Rework Systems


Supported by : 부경대학교


  1. J. Lee, J. H. Kim, C. D. Yoo, "Thermosonic Bonding of Lead-Free Solder with Metal Bump for Flip-Chip Bonding", Journal of Electronic Materials, Vol.34, Issue 1, pp. 96-102, 2005. DOI:
  2. W. S. Hong, W. S. Kim, N. C. Park, K. B. Kim, "Activation Energy for Intermetallic Compound Formation of Sn-40Pb/Cu and Sn-3.0Ag-0.5Cu/ Cu Solder Joints", Journal of KWJS, Vol. 25, No. 2, April, 2007 DOI:
  3. Y. Kim, S. Kim, "The Design of Fuzzy P+ID Controller for Brushless DC Motor Speed Control", Journal of the Korea Academia-Industrial cooperation Society, Vol. 7, No. 5, pp. 823-829, 2006
  4. H. Cho, "A Study on the Speed Control of Induction Motor using a PID Controller and Neural Network Controller", Journal of the Korea Academia-Industrial cooperation Society, Vol. 10, No. 8, pp. 1993-1997, 2009 DOI:
  5. HAKKO, SMD rework system, (accessed July, 21, 2014)
  6. D. Lim, Y. Kim, K. Chong, "The linear model analysis and Fuzzy controller design of the ship using the Nomoto model", Journal of the Korea Academia-Industrial cooperation Society, Vol. 12, No. 2 pp. 821-828, 2011 DOI:
  7. G. Kang, W. Lee, "Design of TSK fuzzy controller based on TSK fuzzy model", Journal of the Korean Institute of Telematics and Electronics S., Vol. 35, No. 11, pp.53-67, 1998. DOI:
  8. G. Kang, K. Oh, "Design of Fuzzy PID controllers using TSK Fuzzy Systems", International Journal of Fuzzy Logic and Intelligent Systems, Vol. 24, No. 11, pp.102-109, 2014. DOI:
  9. M. Sugeno, G.T. Kang, "Structure identification of fuzzy model," Fuzzy Sets and Systems, Vol. 28, No. 1, pp. 15-33, 1988. DOI:

Cited by

  1. A soldering station controller for two types heater vol.19, pp.3, 2015,